曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  missing. 
R  (b) Make sure there is no loose seal on the aircraft. 
R  (c) Make a note in the aircraft log that the seal has been removed. 
R  (2) To repair damage to the fixed fairing seals: 
R  NOTE : Be careful not to damage the adjacent structure when you____ 
R  remove loose or damaged seal. 
R  (a) Cut and remove loose or damaged pieces of the seal. 
R  (b) Use a MISCELLANEOUS (Material No. 19-003), made moist with 
R  CLEANING AGENTS (Material No. 11-026) to clean the area around 
R  the removed seal. 
R  (c) Apply the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-052) to 
R  the area where the damaged seal has been removed. 
R  (d) Apply the tape between the fairing and the bottom wing skin. Make 
R  sure that it gives the same seal effect as the initial seal.

 

R  (e) Make the tape smooth from the center to the edges to remove air 
R  bubbles and push the edges down tightly. 
R  NOTE : When you cut the tape, make sure there are no cuts or____ 
R  overlaps in the direction of flight. 
R  (3) Make a note in the aircraft log that the seal has been repaired. 
R  5. Close-up________ 
R  Subtask 57-55-00-410-050 
R  A. Close Access 
R  (1) Remove the access platform(s). 
R  Subtask 57-55-00-865-063 
R  B. Make sure that this(these) circuit breaker(s) is(are) closed: 
R  6CV, 8CV. 
R  Subtask 57-55-00-942-054 
R  C. Removal of Equipment 
R  (1) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (2) Remove the warning notice(s). 
R  (3) Remove the safety barriers. 
R  (4) Remove the ground support and maintenance equipment, the special and 
R  standard tools and all other items.

R TASK 57-55-00-440-004

R  Restoration of the Aircraft for Flight after Damage to Flap-Track Fairing Seals 
R  WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ 
R  START A TASK ON OR NEAR: 
R  - THE FLIGHT CONTROLS 
R  - THE FLIGHT CONTROL SURFACES 
R  - THE LANDING GEAR AND THE RELATED DOORS 
R  - COMPONENTS THAT MOVE. 
R  WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ 
R  GEAR. 
R  CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. 
R  - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. 
R  INCORRECT INSTALLATION CAN CAUSE DAMAGE. 
R  1. Reason for the Job__________________ 
R  Refer to the CDL TASK: 27-13 
R  Flap Track Fairing Seals 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE  QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific  safety barriers 
R  No specific  warning notices 
R  No specific  adjustable access platform 3.5 m (11 ft. 6 in.) 
R  98D27803500001  1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER

 

 B. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-009  Retraction of the Flaps on the Ground
 57-55-11-000-001  Removal of the Flap Track Fairings Nos. 2, 3 and 4
 57-55-11-000-004  Removal of the Flap Track Fairings Nos. 2, 3 and 4
 57-55-11-400-001  Installation of the Flap Track Fairings Nos. 2, 3 and
 4
 57-55-11-400-004  Installation of the Flap Track Fairings Nos. 2, 3 and
 4
 CMM 57-55-12  (for corrective action)
 CMM 57-55-13  (for corrective action)
 CMM 57-55-14  (for corrective action)
 CMM 57-55-15  (for corrective action)
 CMM 57-55-16  (for corrective action)
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(50)