Spoilers 2 thru 5 - Inspection Area
Figure 601/TASK 57-72-00-991-001
1EFF : ALL 1 57-72-00 Page 604
1 1 Feb 01/98
1 1
1CES 1
Subtask 57-72-00-210-051
B. Inspection
(1) Examine the area of the center hinge fitting. Make sure that:
-
there are no cracks
-
there is no damage
-
there are no signs of delamination
-
there is no corrosion at the metal attachment points
-the surface protection is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 577000) for the
____
correct repair procedure.
5. Close-up
________ Subtask 57-72-00-865-051
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-72-00-860-051
B. Aircraft Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Retract the spoilers (Ref. TASK 27-60-00-866-002).
(3)
On the servo-control, make sure that the pointer on the hex-head is opposite the letter 'O' (Operation) on the housing.
Subtask 57-72-00-942-054
C. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-72-00Page 605 1 1 Aug 01/99R 1 1 1CES 1
TASK 57-72-00-200-003
Detailed Visual Inspection of Spoilers 2, 3, 4 and 5 Upper and Lower Skins at Trailing Edge and Inboard and Outboard Edges
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
R R R R R CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job__________________
Refer to the MPD TASK: 577008-01
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific No specific safety barrierswarning noticesaccess platform 3 m (9 ft. 10 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-60-00-866-002 Extension-Retraction of the Spoilers for Maintenance ASRM 577000 (for corrective action) 57-72-00-991-002 Fig. 602
3. Job Set-up
__________
Subtask 57-72-00-941-052
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put warning notices in the cockpit to tell persons not to operate the spoilers.
(3)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
Subtask 57-72-00-860-052
B. Aircraft Maintenance Configuration
(1)
Put the access platform below the applicable spoiler:
-
for spoiler 2, zone 583 (683)
-
for spoiler 3, zone 584 (684)
-
for spoiler 4, zone 585 (685)
-
for spoiler 5, zone 586 (686).
(2)
Do a manual extension of the spoilers (Ref. TASK 27-60-00-866-002).
1EFF : ALL 1 57-72-00Page 607 1 1 Aug 01/99R 1 1 1CES 1
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(101)
