-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575316-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific access platform 2.5 m (8 ft. 2 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-061A D DAN 220
ALUMINIUM FOIL ADHESIVE TAPE (Ref. 20-31-00) Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page A644 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 27-54-62-000-003 Removal of the Leading Edge Panels 2 and 5 on the
Outboard Flap 27-54-62-400-003 Installation of the Leading Edge Panels 2 and 5 on
the Outboard Flap 57-55-11-000-001 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-400-001 Installation of the Flap Track Fairings Nos. 2, 3 and
4
ASRM 575321 (for corrective action)
R **ON A/C 106-149, 215-299, 401-499,
57-53-00-991-020-A Fig. 619A
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-214,
57-53-00-991-023 Fig. 621
R **ON A/C 106-149, 215-299, 401-499,
57-53-00-991-023-A Fig. 621A
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
3. Job Set-up
__________
Subtask 57-53-00-941-075
A. Safety Precautions
(1)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(2)
Put the safety barriers in position.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page A645 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 57-53-00-860-121
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Fully extend the flaps (Ref. TASK 27-50-00-866-008).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is on the slat/flap control lever.
Subtask 57-53-00-865-103
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-214,
Subtask 57-53-00-010-072
D. Get Access
(Ref. Fig. 621/TASK 57-53-00-991-023)
(1)
Put the access platform below the applicable wing trailing edge at flap track 4, zone 533 (633).
(2)
Remove the applicable access panels (Ref. TASK 57-55-11-000-001):
-
for the left wing, remove 533AT, 533CB
-
for the right wing, remove 633AT, 633CB.
(3)
Remove the outboard flap leading edge panel 5 (Ref. TASK 27-54-62-000-003).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page A646 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Outboard Flap - Inspection
Figure 621/TASK 57-53-00-991-023
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 57-53-00Page A647 1201-214, 1May 01/05 1 1 1CES 1
R **ON A/C 106-149, 215-299, 401-499,
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(2)
