(2)
Remove the applicable flap track fairing (Ref. TASK 57-55-11-000-004):
-
for the left wing, remove 532AT, 532CB
-
for the right wing, remove 632AT, 632CB.
(3)
Put the spark-proof lamp adjacent to the inspection area.
4. Procedure
_________
(Ref. Fig. 627/TASK 57-53-00-991-031)
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-53-00-110-082
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the drive linkage and drive fitting.
1EFF : 301-399, 1 57-53-00Page A690 1 1 Nov 01/04R 1 1 1CES 1
Outboard Flap - Track 3 Drive Linkage and Drive Fitting - Inspection Area Figure 627/TASK 57-53-00-991-031
1EFF : 301-399, 1 57-53-00Page A691 1 1 Nov 01/04R 1 1 1CES 1
Subtask 57-53-00-210-072
B. Inspection
(1) Do an inspection of the drive linkage and the drive fitting. Make sure that:
-
there is no damage
-
there is no corrosion
-
there are no cracks or scores
-
the drive linkage and the drive fitting are correctly installed
-
the surface protection is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575300) for the
____
correct repair procedure.
5. Close-up
________ Subtask 57-53-00-410-077
A. Close Access
(1)
Remove the spark-proof lamp from the inspection area.
(2)
Install the applicable flap track fairing (Ref. TASK 57-55-11-400-004):
-
for the left wing, install 532AT, 532CB
-
for the right wing, install 632AT, 632CB.
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 57-53-00-865-116
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-53-00-860-059
C. Aircraft Maintenance Configuration
(1) Fully retract the flaps (Ref. TASK 27-50-00-866-009).
1EFF : 301-399, 1 57-53-00Page A692 1 1 Nov 01/04R 1 1 1CES 1
Subtask 57-53-00-942-081
D. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : 301-399, 1 57-53-00Page A693 1 1 Nov 01/04R 1 1 1CES 1
TASK 57-53-00-210-004
Detailed Visual Inspection of Outboard Double Slotted Flap, Internal Support Fitting at Track 4, Including Pendulum Support, Drive Bracket ....
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575333-01 Detailed visual Inspection of Outboard Double Slotted Flap, Internal Support Fitting at Track 4, Including Pendulum Support, Drive Bracket and Attachment Structure, Internal and External, LH/RH
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(13)
