2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific spark-proof lamp No specific warning notice No specific access platform 2.5 m (8 ft. 2 in.) 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
R 1EFF : 301-399, 1 57-53-00Page A662 1 1 May 01/05 1 1 1CES 1

 INTENTIONALLY BLANK

R 1 1 57-53-00Page A663 1 1 May 01/05 1 1 1CES 1

 INTENTIONALLY BLANK

R 1 1 57-53-00Page A664 1 1 May 01/05 1 1 1CES 1 B. Consumable Materials

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-061A D DAN 220
 ALUMINIUM FOIL ADHESIVE TAPE (Ref. 20-31-00) Material No. 11-026 GB DEF-STAN 68-148/1
 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 27-54-61-000-002 Removal of the Flap Kink-Seals 27-54-61-400-006 Installation of the Flap Kink-Seals ASRM 575221 (for corrective action) 57-53-00-991-027 Fig. 623
 3. Job Set-up
__________
 Subtask 57-53-00-941-080
 A. Safety Precautions
 (1)
 Put a warning notice on the flap/slat control lever (panel 114VU) to tell persons not to operate the flaps.

 (2)
 Put the safety barriers in position.

 Subtask 57-53-00-860-050
 B. Aircraft Maintenance Configuration
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 (1) Fully extend the flaps (Ref. TASK 27-50-00-866-008).
 1EFF : 301-399, 1 57-53-00Page A665 1 1 Nov 01/04R 1 1 1CES 1

 (2) Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed on the flap/slat control lever on the panel 114VU.
 Subtask 57-53-00-865-107
 C. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
 Subtask 57-53-00-010-074
 D. Get Access
 (1)
 Put the access platform in position below the inboard rib of the outboard flap at zone 587(687).

 (2)
 Remove the flap kink-seals (Ref. TASK 27-54-61-000-002).

 (3)
 Remove and discard the inspection hole covers.

 (4)
 Put the spark-proof lamp adjacent to the inspection area.

 4. Procedure
_________ (Ref. Fig. 623/TASK 57-53-00-991-027) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
 EDGE:

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 Subtask 57-53-00-110-079
 A. Preparation for Inspection
 (1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the outboard double slotted flap inboard rib, including interconnection strut attachment bracket, lever and roller internal and external.
 1EFF : 301-399, 1 57-53-00Page A666 1 1 Nov 01/04R 1 1 1CES 1

 Outboard Flap - Inboard Rib - Inspection Area
 Figure 623/TASK 57-53-00-991-027

 1EFF : 301-399, 1 57-53-00Page A667 1 1 Nov 01/04R 1 1 1CES 1

 Subtask 57-53-00-210-070
 B. Detailed Visual Inspection of Outboard Double Slotted Flap Inboard Rib, Including Interconnection Strut Attachment Bracket, Lever and Roller, Internal and External, LH/RH
 (1) Do an inspection of the rib, interconnection strut attachment bracket, lever and roller. Make sure that:
 -
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(6)