曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  (l) Apply a thin layer of SEALANTS (Material No. 09-018) or SEALANTS 
R  (Material No. 09-019) to the movable fairing interface with the 
R  top cover (10). 
R  (m) Apply a thin layer of SPECIAL MATERIALS (Material No. 05-064) to 
R  the top cover interface with the movable fairing. 
R  (n) Apply a thin layer of SPECIAL MATERIALS (Material No. 05-002) to 
R  the screws (11). 
R  (o) Install the top cover (10) with the screws (11). 
R  (p) Apply a bead of SEALANTS (Material No. 09-016) into the groove 
R  between the top cover (10) and the movable fairing. 
R  (q) Use CLEANING AGENTS (Material No. 11-004) and a plastic spatula, 
R  to make the bead smooth and level with the fairings. 
R  Subtask 57-55-11-865-061 
R  D. Remove the safety clip(s) and the tag(s) and close this(these) circuit 
R  breaker(s): 
R  6CV, 8CV. 
R  Subtask 57-55-11-860-062 
R  E. Aircraft Configuration 
R  (1) Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat 
R  control-lever. 
R  Subtask 57-55-11-710-055 
R  F. Test 
R  (1) Do an operational test of the flap system (Ref. TASK 27-54-00-710-
R  001). Make sure that the movable fairing operates correctly.

 

R  5. Close-up________ 
R  Subtask 57-55-11-942-057 
R  A. Removal of Equipment 
R  (1) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (2) Remove the access platform(s). 
R  (3) Remove the warning notice(s). 
R  (4) Remove the safety barriers. 
R  (5) Remove the ground support and maintenance equipment, the special and 
R  standard tools and all other items.

 

 TASK 57-55-11-000-005
 Removal of the Inboard and Outboard Flap Tab Hinge-Fairings
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific safety barriers
 No specific warning notice
 No specific access platform 2.5 m (8 ft. 2 in.)
 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-009 Retraction of the Flaps on the Ground
R  57-55-11-991-014-A Fig. 413 57-55-11-991-018 Fig. 414 57-55-11-991-017 Fig. 415

R  3. Job Set-up__________ 
R  Subtask 57-55-11-941-066 
R  A. Safety Precautions 
R  (1) Put a warning notice on panel 114VU to tell persons not to operate 
R  the flaps or slats. 
R  (2) Put the safety barriers in position. 
R  Subtask 57-55-11-860-052 
R  B. Aircraft Maintenance Configuration 
R  (1) Put the flaps in the fully retracted position (Ref. TASK 27-50-00-
R  866-009). 
R  (2) Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) 
R  on the flap/slat control lever. 
R  Subtask 57-55-11-865-062 
R  C. Open, safety and tag this(these) circuit breaker(s): 
R  -------------------------------------------------------------------------------
R  PANEL DESIGNATION IDENT. LOCATION 
R  -------------------------------------------------------------------------------
R  49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 
R  121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21 
R  Subtask 57-55-11-010-057 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(70)