-
there is no corrosion
-
there are no cracks or scores
-
the surface protection is in the correct condition
-
the attachment bolts are tight
-there is not too much play of the roller.
(Ref. Fig. 623/TASK 57-53-00-991-027)
NOTE : If the AXIAL PLAY "X" or the RADIAL PLAY "Y" is more than 0.25
____ mm (0.0098 in.), do a check of the liner for damage and wear.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575221) for the
____
correct repair procedure.
5. Close-up
________
Subtask 57-53-00-410-073
A. Close Access
(1)
Remove the spark-proof lamp from the inspection area.
(2)
Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A), cut to the correct dimensions, to make the inspection covers.
(3)
Install the inspection covers.
(4)
Install the flap kink-seals (Ref. TASK 27-54-61-400-006).
(5)
Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 57-53-00-865-108
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
1EFF : 301-399, 1 57-53-00Page A668 1 1 Nov 01/04R 1 1 1CES 1
Subtask 57-53-00-860-051
C. Aircraft Maintenance Configuration
(1) Fully retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-53-00-942-077
D. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : 301-399, 1 57-53-00Page A669 1 1 Nov 01/04R 1 1 1CES 1
TASK 57-53-00-220-014
Special Detailed Inspection of Outboard Double Slotted Flap Inboard Rib, Including Interconnection Strut Attachment Bracket, Lever and Roller ....
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575327-02
Special Detailed Inspection of Outboard Double Slotted Flap Inboard Rib,
Including Interconnection Strut Attachment Bracket, Lever and Roller,
Internal And External, LH/RH
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific spark-proof lamp No specific warning notice No specific access platform 2.5 m (8 ft. 2 in.)
1EFF : 301-399, 1 57-53-00Page A670 1 1 Nov 01/04R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-061A D DAN 220
ALUMINIUM FOIL ADHESIVE TAPE (Ref. 20-31-00) Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 27-54-61-000-002 Removal of the Flap Kink-Seals 27-54-61-400-006 Installation of the Flap Kink-Seals NTM 575327 PART 9 ASRM 575300 (for corrective action) 57-53-00-991-028 Fig. 624
3. Job Set-up
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼5(7)
