(f)  
Install the breather adapter (2) in the PWC 41445 support.

 (g)  
Remove the carbon seal (1) from the APU oil.

 (h)  
Use the drift to install the carbon seal (1) into the breather adapter (2).

 S 414-029
 (2)  
Install the breather adapter (1) (Fig. 401):

 (a)  
Install the new packings (5), lubricated with engine oil, on the transfer tube (2).

 (b)  
Install the transfer tube (2) in the vent tube adapter (3) on the accessory gearbox (4). 1) Make sure the flow arrow on the tube (2) points to the

 breather adapter (1).

 (c)  
Install the new packing (6), lubricated with engine oil, on the breather adapter (1).

 (d)  
Install the breather adapter (1) on the end of the transfer tube (2).

 CAUTION: MAKE SURE THE CARBON SEAL CORRECTLY ALIGNS WITH THE
_______ GEARBOX HOUSING DURING THE INSTALLATION. LEAKAGE OF THE SEAL CAN OCCUR IF THE SEAL DOES NOT ALIGN CORRECTLY.
 (e)
Install the breather adapter (1) on the accessory gearbox (4).

 1)  Make sure the carbon seal correctly aligns with the gearbox housing when you install the adapter.

 (f)  
Install the two washers (7) and the nuts (8). 1) Tighten nuts (8) to 32-36 pound-inches (3.6-4.0 N.m).

 (g)  
Install the flexible hose (10) on the breather adapter (1). 1) Tighten the clamp (9).

 (3)  
Do this task: "Fill the APU Oil Tank" (Ref 12-22-02/301).

 (4)  
Do this task: "Start and Operate the APU" (Ref 49-11-00/201).

 (5)  
During the APU operation, examine the engine for oil leakage.

 S 614-021
 S 864-023
 S 794-024
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-27-01
 ALL  ú ú 01 Page 407 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (6)  S 864-025Do this task:  "Usual APU Shutdown" (Ref 49-11-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-27-01
 ALL  ú ú 01 Page 408 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 MAIN DRIVESHAFT OIL SEAL - REMOVAL/INSTALLATION
_______________________________________________
 1.  General_______
 A.  This procedure has these tasks:
 (1)  
A removal of the main driveshaft oil seal

 (2)  
An installation of the main driveshaft oil seal.

 B.  
The main driveshaft oil seal or plain seal is referred to as the oil seal.

 C.  
The oil seal is installed on the main driveshaft assembly of the accessory gearbox. You can get access to the oil seal through the two APU access doors.

 TASK 49-27-02-004-018
 2.  Main Driveshaft Oil Seal Removal (Fig. 401)________________________________
 A.  References
 (1)  
AMM 12-22-02/301, Auxiliary Power Unit

 (2)  
AMM 49-41-01/401, Starter Motor

 B.  
Equipment

 (1)  
PWC41383 Extractor - Seal (or equivalent tool)
 Pratt & Whitney Canada

 C.  
Access

 (1)  
Location Zones 221 Control Cabin - Left 222 Control Cabin - Right 310 Fuselage - Station 2360 to Station 2792

 (2)  
Access Panels
 317AL APU Access Door - Left
 318AR APU Access Door - Right

 D.  
Prepare for the Removal

 (1)
Do this task: Starter Motor Removal (AMM 49-41-01/401).

 (2)  
Do this task: Drain the APU Oil (AMM 12-22-02/301).

 S 024-034
 S 684-002
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 2(10)