(d)
Make sure the insulation covers correctly attach to the APU compartment firewall.
(e)
Close the APU access doors.
(f)
Close the latches on the APU access doors.
S 864-026
(3)
Remove the DO-NOT-OPERATE tag from the APU control switch on the P5 panel.
S 864-025
(4)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P83 Panel, E8 Aft Equipment Center
1) APU PRIMARY CONT
(b)
P6 Main Power Distribution Panel
1) 6K18 APU ALTN CONT
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
49-61-05
ALL ú ú 01 Page 409 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
TASK 49-61-05-404-037
6. T12 Air Temperature Sensor Installation (Fig. 402)_______________________________________
A. References
(1)
WDM 49-11-18
(2)
SSM 49-11-01
B. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 402 | 17 | Temperature Sensor (Load | 49-61-05 | 01 | 105 | | | | Compressor Inlet Temperature | | | | | | | Sensor T12) | | | | | | 18 | Gasket | | | 110 | 2.......….......…...................................…...........…......….......1
C. Access
(1)
Location Zone
318 APU Compartment-Lower Forward Side of APU on Air Inlet Plenum, RH
(2)
Access Panel
317AL APU Access Door
318AR APU Access Door
D.
Procedure
S 434-038
CAUTION:_______DO NOT HIT THE INLET PLENUM WITH YOUR HANDS OR TOOLS. THIS CAN CAUSE DAMAGE TO THE INLET PLENUM. IF YOU CAUSE DAMAGE TO THE INLET PLENUM, IT WILL BE NECESSARY TO REPLACE IT.
(1)
Install the T12 sensor (17).
(a)
Install a new copper gasket (18) on the T12 sensor (17).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
49-61-05
ALL ú ú 01 Page 410 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b)
Put the T12 sensor (17) in the compressor inlet case.
(c)
Install a jamnut on the T12 sensor (17).
(d)
Tighten the jamnut to 150-170 pound-inches (17.0-19.0
newton-meters).
(e)
Remove the dust caps from the electrical connector (16).
(f)
Connect the P23 connector (16) to the T12 sensor (17), and tighten it with your hand.
NOTE: The connector is fully tight when the lock indicator is
____
in the orange color band.
S 414-045
(2)
Close the APU access doors:
(a)
Do a visual check of the EGT bus bars:
1) Make sure the bus bars are not damaged.
2) Make sure no metal parts touch the bus bars.
3) Make sure the bus bars do not touch each other.
(b)
Disengage the support rods for the APU access doors.
(c)
Put the support rods in the clips on the inner side of the APU access doors.
(d)
Make sure the insulation covers correctly attach to the APU compartment firewall.
(e)
Close the APU access doors.
(f)
Close the latches on the APU access doors.
S 864-044
(3)
Remove the tag DO-NOT-OPERATE tag from the APU control switch on the P5 panel.
S 864-043
(4)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P83 Panel, E8 Aft Equipment Center
1) APU PRIMARY CONT
(b)
P6 Main Power Distribution Panel
1) 6K18 APU ALTN CONT
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 2(121)
