(b)  
While you hold the diverter valve muffler (5), remove the two coupling clamps (4).

 (c)  
Remove the diverter valve muffler (5).

 (d)  
Remove the clamp (6).

 (e)  
Make sure you install all necessary protection covers.

 TASK 49-52-05-404-012
 3.  Diverter Valve Muffler Installation (Fig. 401)___________________________________
 A. Equipment
 (1)  Mallet - Rubber (commercially available)
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-52-05
 ALL  ú ú 02 Page 402 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400 MAINTENANCE MANUAL
SEE B
SEE A
FWD
APU COMPARTMENT
FWD
A
EXHAUST2. BRACKET DUCT
3.
 BOLT

4.
 COUPLING CLAMP (2 LOCATIONS)

5.
 DIVERTER VALVE MUFFLER

1. NUT 6. CLAMP
FWD
B
Diverter Valve Muffler Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-52-05
 ALL  ú ú 07 Page 403 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L46770
A
747-400
MAINTENANCE MANUAL

 B. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | | 5 | Diverter Duct Muffler (Diverter | 49-52-05 | 01 | 90 | | | | Valve Muffler) | | | | 2.......….......…...................................…...........…......….......1
 C. Access
 (1)  
Location Zones
 221 Control Cabin - Left
 222 Control Cabin - Right
 310 Fuselage - Station 2360 to Station 2792

 (2)  
Access Panels
 317AL APU Access Door - Left
 318AR APU Access Door - Right

 D.
Procedure

 S 424-026
 CAUTION: REMOVE THE PROTECTION COVERS FROM THE OPENINGS AS NECESSARY.
_______ IF YOU DO NOT REMOVE THE PROTECTION COVERS, DAMAGE TO THE APU CAN OCCUR.
 (1)  
Do these steps to install the diverter valve muffler (5):

 (a)  
Install the clamp (6) loosely on the diverter valve muffler (5).

 (b)  
Install the two coupling clamps (4) loosely on the flanges of the diverter valve and exhaust duct.

 (c)  
While you hold the diverter valve muffler (5), align the locating pin on the diverter valve muffler with the hole on the exhaust duct flange and install the diverter valve muffler.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-52-05
 ALL  ú ú 04 Page 404 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (d)  
Install the coupling clamp (4) on the flanges of the diverter valve muffler (5) and exhaust duct. 1) Tighten the nut on the coupling clamp (4) to 70-84

 inch-pounds (7.9-9.5 newton-meters).

 (e)  
While you hold the diverter valve muffler (5), install the coupling clamp (4) on the flanges of the diverter valve muffler and diverter valve. 1) Tighten the nut on the coupling clamp (4) to 70-84

 inch-pounds (7.9-9.5 newton-meters).

 (f)  
Lightly tap the edge of the two coupling clamps (4) with a rubber mallet.

 (g)  
Tighten the two nuts to 100-120 inch-pounds (11.3-13.6 newton-meters) and lightly tap the edge of the two coupling clamps (4) again until the torque value stays constant.

 (h)  
Put the clamp (6) over this marking "clamp here" and install the clamp to the bracket (2) with the bolt (3) and nut (1). 1) Tighten the nut (1) to 36-40 inch-pounds (4.1-4.5
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 2(88)