(c)  
Engage the support rods for the APU access doors.

 S 034-005
 (4)  
Remove the filter bypass indicator (3):

 (a)  
Put the container under the filter bypass indicator.

 (b)  
Disconnect the P3 electrical connector (4) from the filter bypass indicator (3). 1) Install a cap on the electrical connector to prevent

 contamination.

 (c)  
Remove the filter bypass indicator (3) and the packing (2). 1) Discard the packing.

 (d)  
Install a plug in the fuel pump port to prevent contamination.

 TASK 49-31-05-404-008
 3.  APU Fuel Filter Bypass Indicator Installation (Fig. 401)_____________________________________________
 A. Consumable Materials
 (1)  
D00207 Lubricant - Packing, MIL-G-7711A

 B.
References

 (1)  
49-11-00/201, Auxiliary Power Unit

 (2)  
WDM 49-11-11

 (3)  
SSM 49-11-01

 C.
Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 2 | Packing | 49-31-03 | 01 | 77 | | | 3 | Filter Bypass Indicator | | | 70 | 2.......….......…...................................…...........…......….......1

 D.
Access

 (1)  
Location Zone 317 APU Compartment-Bottom of APU Fuel Pump, LH 318 APU Compartment-Bottom of APU Fuel Pump, RH

 (2)  
Access Panel
 317AL APU Access Door
 318AR APU Access Door

 E.
Procedure

 S 424-009
 (1)  
Install the filter bypass indicator (3):

 (a)
Lubricate the packing (2) with the lubricant.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-31-05
 ALL  ú ú 01 Page 403 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (b)  
Install the new packing (2) on the filter bypass indicator (3).

 (c)  
Remove the plug from the fuel pump port.

 (d)  
Install the filter bypass indicator (3) in the filter cover.

 1)  Tighten the indicator to 125-150 pound-inches (14.1-16.9 N.m).

 (e)  
Install a lockwire between the filter bypass indicator (3) and the filter cover.

 (f)  
Remove the cap from the P3 electrical connector (4).

 (g)  
Connect the P3 electrical connector (4) to the filter bypass indicator (3). 1) Tighten the connector with your hand.

 NOTE: The connector is fully tight when you cannot see
____
 the red color band.

 S 864-014
 (2)  
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P83 Panel, E8 Aft Equipment Center
 1) APU PRIMARY CONT

 (b)  
P6 Main Power Supply Panel
 1) 6K18, APU ALTN CONT

 S 864-015
 (3)  
Remove the DO-NOT-OPERATE tag from the APU control switch on the P5 panel.

 S 794-017

 (4)  
Do a check of the installation for leakage:

 (a)  
Do this task: "APU Starting and Operation" (Ref 49-11-00/201).

 (b)  
Examine the installation of the filter bypass indicator for leakage during the APU operation.

 (c)  
Do this task: "APU Usual Shutdown" (Ref 49-11-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-31-05
 ALL  ú ú 01 Page 404 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (d)  If you found leakage, repair the cause of it.
 S 414-016
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機載輔助動力 2(53)