32-41-00
 ALL  ú ú 01 Page 208 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 HYDRAULIC BRAKE SYSTEM - ADJUSTMENT/TEST
________________________________________
 1.  General
_______
 A.  After repair or replacement of linkage or cables, the mechanical portion of the brake control system must be adjusted (rigged).
 B.  Do a test for the hydraulic brake system to examine the function of all the system. The tests are made on a periodic inspection or on a brake malfunction report. A check is done for the pressure at the accumulator and the brake lines. A check is done for the brakes for correct operation and for automatic response.
 C.  The temperature of the airplane must be stable for one hour before rigging.
 TASK 32-41-00-825-001
 2.  Adjust the Hydraulic Brake System
_________________________________
 A.  Standard Tools and Equipment
 (1)  Rigging pins - B-1, 0.309/0.311-inch diameter by 12.7 inches long (four necessary).
 NOTE: These rigging pins are part of F70207-69 or F70207-78
____
 (2)  
Cable Tensiometer - 0 to 200 pounds capacity

 B.  
References

 (1)  
AMM 29-15-00/201, Hydraulic Systems

 (2)  
AMM 32-41-97/401, Brake Feel Augmentor

 C.  
Access

 (1)  
Location Zone
 101 Control Cabin - Left
 102 Control Cabin - Right
 216 Left Main Wheel Well
 217 Right Main Wheel Well
 310 Left Main Landing Gear
 410 Right Main Landing Gear

 D.  
Adjust the Brake Control Linkage

 (1)  
Put chocks on the wheels and release the parking brake.

 S 845-003

 (2)  
Operate the rudder pedal adjustment crank (Fig. 501) to put the rudder pedals of the captain or the first officer in the neutral position.

 S 495-002
 NOTE: Count the number of times the crank turns from the full
____ forward and the full aft adjustment to find the middle position.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-00
 ALL  ú ú 01 Page 501 ú Nov 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 495-004
 (3)  Install a rigging pin through the floor beams and the bellcranks
 below each pair of rudder pedals.
 S 495-005
 (4)  Install the rigging pins through each pair of rudder pedal arms.
 NOTE:____ To permit the rigging pin installation in the rudder pedal
 arms, adjust the tie rods (Fig. 501) by the procedure that
 follows.

 S 035-006
 (5)  
Disconnect the right ends of the tie rods.

 S 495-007

 (6)  
Install the rigging pins through the bellcranks.

 S 035-008

 (7)  
Loosen the jamnuts and adjust the length of the tie rods until you can freely install the rod end bolts.

 S 435-009

 (8)  
Tighten the jamnuts and replace the rod end bolts.

 S 215-010

 (9)  
Make sure that the rig pins are loose.

 S 215-094

 (10)
 Make sure that the rod end threads cover at least half of the inspection hole.

 NOTE: This will make sure the rod end is correctly engaged.
____
 S 825-011
 (11) Put a square against each brake pedal and adjust the pushrod until the pedal tips are 3.06 +0.26/-0.21 inches from the square (Fig. 501).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-00
 ALL  ú ú 02 Page 502 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
BRAKE
CABLES

SEE A
1 3.06 +0.26/-0.21
SQUARE
A-A
1
ASYMMETRY LIMIT MAXIMUM ALLOWABLE MISMATCH BETWEEN ADJACENT PEDAL IS
0.25 INCHES PUSHRODS
CABIN FLOOR BEAM
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 3(11)