曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 NOTE: You can see the brakes "apply" and "release" if you
____ watch the brake wear pins move. The pins will extend farther out of the carrier when the brake releases (AMM 32-41-41/601).
 CAUTION: WHEN YOU TURN THE ANTISKID TRANSDUCER, DO NOT ATTACH
_______ A METAL FITTING DIRECTLY ON THE TRANSDUCER. DAMAGE TO THE EQUIPMENT CAN OCCUR. IF YOU USE A METAL FITTING, PUT A PROTECTIVE COVER ON THE ANTISKID TRANSDUCER.
 1) Turn the right outboard transducer drive coupling to
 approximately 500-1000 RPM. 2) Make sure that the left outboard brake releases. 3) Stop the movement of the brake as quickly as it is
 possible. 4) Make sure that the right outboard brake releases momentarily and then applies again in 5 to 10 seconds.
 (o)  
Open this circuit breaker on the the P6 main power distibution panel: 1) ANTISKID FAIL WARN & PARK BRAKE

 (p)  
Release the parking brake.

 (q)  
Connect the electrical connector D928 to the shutoff valve.

 (r)  
Make sure that the ANTISKID INOP light goes off.

 (s)  
Close this circuit breaker on the main power distribution panel P6: 1) ANTISKID FAIL WARN & PARK BRAKE

 S 424-021
 (11)
 Complete the installation of the transducer as follows:

 (a)  
Put the hubcap on the wheel and turn it if it is necessary to engage the spider on the hubcap with the drive coupling on the transducer.

 (b)  
Attach the hubcap to the wheel with three sets of bolts and washers.

 (c)  
Install lockwire.

 (d)  
On an outboard wheel,
 install the hubcap fairing.

 (e)  
Set the parking brake.

 (f)  
Close the AUTOSLAT circuit breakers on the P6 main power distibution panel.

 (g)  
Remove electrical power if it is not necessary
 (AMM 24-22-00/201).

 (h)  
Remove hydraulic power from systems A and B if it is not necessary (AMM 29-15-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-42-11
 ALL  ú ú 02 Page 407 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 ANTISKID CONTROL UNIT - REMOVAL/INSTALLATION
____________________________________________
 1.  General
 A.  This procedure removes and installs the antiskid control shield.
 B.  The antiskid control unit is found on the E3-2 shelf of the electrical bay (aft and to the right of the access hatch).
 TASK 32-42-21-004-001
 2.  Antiskid Control Unit Removal_____________________________
 A.  Access
 (1)  
Location Zone
 202 Lower Nose Compartment

 B.  
Procedure

 S 844-002
 (1)
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
LANDING GEAR ANTISKID INBD

 (b)  
LANDING GEAR ANTISKID OUTBD

 (c)  
ANTISKID FAIL WRN & PARK BK

 S 024-003
 (2)  Release the latch and move the unit off the rack.
 TASK 32-42-21-404-004
 3.  Antiskid Control Unit Installation__________________________________
 A.  Access
 (1)  
Location Zone
 202 Lower Nose Compartment

 B.  
Procedure

 S 214-005
 (1)  
Make sure the contact pins on the control unit and the mating connector are straight.

 S 424-006

 (2)  
Move the control unit on the rack and safety the latch.

 S 724-007

 (3)  
When the antiskid control unit is replaced, do the antiskid system test that follows.

 TASK 32-42-21-704-008
 4.  Antiskid Control Unit Test___________________________
 A.  General
 (1)  
Do the test of the antiskid control unit if you replaced the antiskid control unit.

 B.  
References

 (1)  
24-22-00/201, Manual Control

 (2)  
32-00-01/201, Ground Locks

 (3)  
32-42-00/501, Antiskid System

 (4)  
32-43-01/501, Automatic Braking System

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 3(63)