32-51-41
 ALL  ú ú 01 Page 401 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
NWSB TURNBUCKLE
NWSA SEE B
TURNBUCKLE
NWSA 2. RIG PIN 1. STEERING SEE A TURNBUCKLE WHEEL
A
19. WASHER
NWSA CABLE
3.
SIDEWALL

4.
CABLE DRUM

5.
COTTER PIN

6.
SPACER

7.
SPACER

8.
BEARING

18. SHAFT NUT
9. BUTTON PLUG
17. SHAFT 10. WHEEL NUT
16. WASHER
11. BEARING RETAINER15. OUTBOARD BEARING
14. COTTER KEY
13. HOUSING 12. BUTTON
PLUG AND NWSB CABLE
RIG PIN HOLE
INBD
1. STEERING WHEEL
B
Steering Wheel and Cable Drum Installation Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-41
 ALL  ú ú 01 Page 402 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 034-012
 (11)
 Remove the cotter keys (5 and 14) in the cable drum (4) and remove the cables NWSA and NWSB.

 S 034-013

 (12)
 If it is necessary to remove the housing (13), remove the insulation around the three bolts.

 (a)  
Remove the bolts.

 S 034-014
 (13) Remove the washer (19) and outboard bearing (15) from the housing (13).
 TASK 32-51-41-404-015
 3.  Steering Wheel and Cable Drum Installation (Fig. 401)__________________________________________
 A. Standard Tools and Equipment
 (1)  
Cable Tensiometer

 (2)  
Rigging Pin - 0.311 + 0.000/-0.002 inch diameter x 6.0 inches long

 NOTE: The rigging pin is part of F70207-69 or F70207-78
____
 B. References
 (1)  
AMM 25-21-46/401, Sidewall Panels

 (2)  
AMM 32-51-00/501, Nose Wheel Steering System

 C.
Procedure

 S 434-016
 (1)  
Install the washer (19) and outboard bearing (15) in the housing (13).

 S 434-017

 (2)  
Set the cables in the cable drum (4) and install the cotter keys (5 and 14).

 S 434-018

 (3)  
Set the cable drum (4), the spacer (6 and 7), the bearing (8), and install the shaft (11).

 (a)  
Make sure the index points will line up on the splines.

 (4)  
Install the washer (16) and the shaft nut (18).

 (5)  
Align the cotter pin holes and install the cotter key.

 (6)  
Install the bearing retainer (11) with the three screws.

 (7)  
Install the sidewall (3) (AMM 25-21-46/401).

 S 434-019
 S 434-020
 S 434-021
 S 434-022
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-41
 ALL  ú ú 01 Page 403 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 494-028
 (8)  
Install the rig pin (2).

 S 424-024

 (9)  
Install the steering wheel (1).

 NOTE: The arrow on the steering wheel must align with the arrow on
____
 the sidewall after you install the rigging pin.

 (a)  
Put the steering wheel (1) in its position for attachment to the shaft of the tiller assembly.

 (b)  
Install the washer, and the wheel nut (10) to hold the steering wheel (1) to the shaft.

 (c)  
Tighten the wheel nut (10) and measure the torque it takes to run it on the threads of the shaft.

 (d)  
Add 50-75 lb-in torque to the measured run-on torque in the step above and tightened the wheel nut (10) for the final torque.

 NOTE: Make sure the final torque value is below 375 lb-in.
____
 (e)  
Install the button plug (9) on the steering wheel (1).

 (10)
 If it is necessary, tighten the cables (AMM 32-51-00/501).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 3(134)