曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 714-011
 (5)  Look at the pressure shown on the HYD BRAKE PRESS gage on the first officer's panel (P3). Make sure that this pressure is approximately the same as the pressure shown by the direct reading pressure gage.
 NOTE:____You can only calibrate the transmitter during overhaul. You can not adjust the transmitter after you install it.
 S 784-012
 (6)  
Remove the power from hydraulic systems (AMM 29-15-00/201).

 S 794-015

 (7)  
While the parking brake is set, listen and feel for gas leaks at the transmitter.

 G.
Put the Airplane Back to Its Usual Condition

 (1)
Remove electrical power, if it is not necessary (AMM 24-22-00/201).

 S 864-029
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-52
 ALL  ú ú 01 Page 406 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 MAIN GEAR BRAKE SWIVEL - REMOVAL/INSTALLATION
_____________________________________________
 1. General
 A. This procedure removes and installs the main gear brake swivel.
 TASK 32-41-61-004-001
 2.  Remove the Main Gear Brake Swivel (Fig. 401)_________________________________
 A. References
 (1)  
29-15-00/201, Hydraulic System

 B.
Access

 (1)  
Location Zones
 310 Left Main Landing Gear
 410 Right Main Landing Gear

 C.
Procedure

 S 214-002
 (1)  
Make sure that the ground downlocks of the landing gear are engaged.

 S 844-003

 (2)
Put the chocks on the wheels and release the parking brake.

 S 844-004

 (3)  
Remove the pressure from the hydraulic system A and B (AMM 29-15-00/201).

 S 034-005

 (4)  
Disconnect the hydraulic lines connected to the swivel and seal the lines with caps.

 (5)  
Remove the attach bolts from the bracket cap.

 (6)  
Remove the bracket cap and the swivel.

 S 024-006
 S 024-007
 TASK 32-41-61-404-008
 3.  Install Main Gear Brake Swivel (Fig. 401)______________________________
 A. References
 (1)  12-12-00/301, Hydraulic Reservoir
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-61
 ALL  ú ú 02 Page 401 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500MAINTENANCE MANUAL
SEE A
ATTACH BOLTS
BRACKET CAP 
A MAIN GEAR BRAKE SWIVEL ASSEMBLY SEE  TRUNNION LINK 
FWD 
SEE B SWIVEL  FWD 
LINES HYDRAULIC  HYDRAULIC LINES FITTING 
FITTING (DYNAMIC) 
NUT  HOUSING (SWIVEL)  A 
B 
Figure 401 Main Gear Brake Swivel Installation 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-41-61
 ALL  ú ú 01 Page 402 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (2)  
29-15-00/201, Hydraulic System

 B.
Access

 (1)  
Location Zones
 310 Left Main Landing Gear
 410 Right Main Landing Gear

 C.
Procedure

 S 424-020
 WARNING: MAKE SURE THAT THE SWIVEL JOINT AND THE HYDRAULIC LINES ARE
_______ ORIENTED AS SHOWN IN FIG. 401, DETAIL A. THE HYDRAULIC LINE TO THE BRAKE ASSEMBLY MUST BE CONNECTED TO THE SWIVEL HOUSING AND THE HYDRAULIC LINE FROM THE ANTI-SKID VALVE TO THE SWIVEL FITTING AS SHOWN IN FIG. 401, DETAIL B. IF THE ASSEMBLY OF THE SWIVEL AND THE HYDRAULIC LINES ARE ROTATED 180 DEGREES, THE HYDRAULIC LINES CAN BE CONNECTED, BUT THE SWIVEL WILL NOT OPERATE. THIS CAN CAUSE THE HYDRAULIC LINES TO BREAK DURING EXTENSION AND RETRACTION AND CAUSE THE BRAKE PRESSURE TO BE LOST.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 3(32)