曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 Particularly on longer flights, you will transverse through any number of Centers and
Sectors. Expect to be switched to these different centers/controllers from time to time.
Some will require transponder code changes. Simply dial the new code in when it is
assigned. If your co-pilot has the radios, he/she will do this for you.
At approximately 35 miles from BRIBE, things stop, the Flight Simulator freezes.
Remember, we have enabled Pause at Distance on the General Options Tab. You are 140
flying miles from KORD. Consider this feature in your flight planning, especially those long
cross countries or over-the-ocean flights where staying with the sim the entire way might be
impractical. To continue, simply un-pause.
Radar Contact Tutorials
Version 4 December 2, 2007
Copyright JDT LLC 2005 Page 148
Time to Start Down
At approx 34 miles from BRIBE you will be told to “descend
and maintain FL 270”. Descend and maintain is a statement, a
"start down now" clearance. Notice the new option “3 – PD”.
If you wish to stay at FL290 and be more fuel efficient, you
can choose option 3. For now, acknowledge the descent
clearance and start the descent to FL 270. When you near FL
270, the HIGH controller will descend you again to FL 240.
When you near FL 240, the HIGH controller will switch you
to the LOW controller for further descent clearances. You may be descended directly to
FL240. Intermediate descents happen randomly.
The LOW Center controller will issue a PD/"expect" clearance. For purposes of this tutorial,
do not level. Continue your descent to the assigned PD altitude. Do not forget, descending
through FL180, reset your altimeter to the local (Press B).
About 17 miles from JVL you will have another sector switch.
About 2 miles from JVL, the controller will issue "...cross four zero miles from 'ORD' at and
maintain one one thousand, two five zero knots...” or "...cross four zero miles from 'ORD' at
and maintain one two thousand, two five zero knots...”. Another new feature, RC now
determines what runways are active at this point in the flight. If the active is a “near side”
approach (no downwind) the controller needs you a little lower than if the active runway is a
“far side” approach (downwind, base, final). Adjust your speed/rate of descent to meet this
restriction accordingly. You do not have opportunity to “Unable” this clearance with Pilot
Auto-Reply checked.
IMPORTANT NOTE - The PD altitude and crossing restriction clearances have
caused confusion to users since v1. Refer to your manual, the sections Pilot Discretion
Descent Clearances and Crossing Restrictions for in-depth explanations.
As you pass BULLZ, get the arrival ATIS at approx 50 miles
out by using “Lv Freq for Wx” (Press 2). You will make the
request to leave frequency, hear the ATIS loop, and report
"back up" all automatically. And what runway did ATIS say
to expect? Listen!
If you wish (stay ahead of things), use the ILS information displayed on the Menu Display,
below the checkpoint data. This information become available after you report “back up”.
You will see something like <14L>142°/11090. Set the ILS frequency and course data in
your #1 radio now, and 113.90 in Nav2 (ORD VOR frequency).
Radar Contact Tutorials
Version 4 December 2, 2007
Copyright JDT LLC 2005 Page 149
O’Hare Approach
At 40 miles from KORD, Center will switch you to Approach.
We will accept whatever runway Approach needs us on. You
have not received any alternate clearances yet, so continue
towards your final checkpoint, ORD. Follow the clearances
issued by Approach.
While being vectored, take a moment to look through the
menu pages and become acquainted with RC‟s enhancements.
All are covered in later tutorials. For this flight however, as tempting as those features are,
let‟s follow the Approach instructions to landing. Do not forget to reset that altimeter from
time to time. Get after those checklists!
Remember: never exceed 250kts while below 10,000. There will be an initial heading/altitude
clearance that sets you up for pattern entry and eventually you will be turned to downwind
and base. Larger, busy airports have multiple Approach controllers. KORD certainly
qualifies. Contact the Final controller when told to do so.
ATIS named rwy 14L as active at this tutorial‟s writing, calling for full pattern vectors. Your
approach sequence may be different. Simply follow your clearances.
At the appropriate time you will be turned towards the localizer with "American 293, XX
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料15(118)