S 434-018
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-12-02
ALL ú ú 02 Page 404 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 414-019
(5)
Install the strike board (AMM 32-12-03/401).
S 434-020
(6)
Install the bushing in the bracket as shown on detail C, Fig. 401.
S 824-021
(7)
Adjust the inboard door on the wheel well of the wing landing gear (AMM 32-12-00/501).
G.
Put the Airplane in Its Usual Condition
S 434-022
(1) Do this task: "The Installation of the Outboard Door on the Wheel Well of the Wing Landing Gear" (AMM 32-12-01/401).
S 094-027
WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(2)
Do this task: "Removal of the Door Locks from the Wing Landing Gear" (AMM 32-00-30/201).
S 094-029
(3)
Do this task: "Removal of the Door Locks from the Body Landing Gear" (AMM 32-00-30/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-12-02
ALL ú ú 01 Page 405 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
WING LANDING GEAR WHEEL WELL INBOARD DOOR - INSPECTION/CHECK
____________________________________________________________
1. General
_______
A. This procedure contains a task to examine the hinge assemblies of the inboard door on the wing landing gear for worn parts.
B. To do this procedure, you must remove the inboard door of the wheel well on the wing landing gear.
TASK 32-12-02-206-001
2. Wing Landing Gear Wheel Well Inboard Door Inspection (Fig. 601)
____________________________________________________
A. References
(1)
32-12-01/401, Wing Gear Wheel Well Outboard Door
(2)
32-12-02/401, Wing Gear Wheel Well Inboard Door
(3)
IPC 32-12-01 Fig. 2, IPC 32-12-02 Fig. 2, IPC 32-12-03 Fig. 1, IPC 32-12-08 Fig. 1
B.
Access
(1)
Location Zone
731 Wing Landing Gear Door, LH
741 Wing Landing Gear Door, RH
C.
Procedure
S 026-002
(1)
Do this task: "Wing Landing Gear Wheel Well Inboard Door Removal" (Ref 32-12-02/401).
S 016-008
(2)
Do this task: "Wing Landing Gear Wheel Well Outboard Door Removal" (Ref 32-12-01/401).
S 226-004
(3)
Examine the components of the inboard door of the wheel well on the wing landing gear for worn parts.
(a)
Measure the parts at the locations shown in figure 601.
(b)
Compare the measured dimensions to the wear limits in figure
601.
(c)
If the part is not in tolerance, replace the part if you cannot repair it.
S 416-005
(4)
Do this task: "Wing Landing Gear Wheel Well Outboard Door Installation" (Ref 32-12-01/401).
S 426-006
(5)
Do this task: " Wing Landing Gear Wheel Well Inboard Door Installation" (Ref 32-12-02/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-12-02
ALL ú ú 01 Page 601 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
Wing Gear Wheel Well Inboard Door Wear Limits
Figure 601 (Sheet 1)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(100)
