EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-31
ALL ú ú 01 Page 406 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
WING LANDING GEAR AXLE SLEEVE - REMOVAL/INSTALLATION
____________________________________________________
1. General
_______
A. This procedure has two tasks:
(1)
The removal of the axle sleeve from the axle for the wing landing gear (referred to as the axle sleeve).
(2)
The installation of the axle sleeve.
B.
The axle sleeve and the brake housing bushing have an touched fit on the landing gear axle. It is necessary to use the procedure of differential temperature to remove or install these components.
TASK 32-11-32-004-001
2. Wing Landing Gear Axle Sleeve Removal (Fig. 401)
_____________________________________
A. General
(1)
You can not remove the axle sleeve if the brake housing bushing is on the axle.
(2)
This task includes the steps to remove the brake housing bushing.
(3)
It is not necessary to remove the wheel truck to do this task.
B.
Special Tools and Equipment
(1)
G32010 - Puller Equipment, Axle Sleeve
C.
Standard Tools and Equipment
(1)
Heat Blanket - Electrical (300°F maximum)
(2)
Thermometer - Surface Measurement (0° - 350°F)
D.
Consumable Materials
(1)
G00829 Ice - Dry (Commercial Grade)
E.
References
(1)
AMM 09-11-00/201, Towing
(2)
AMM 32-00-30/201, Landing Gear Door Locks
(3)
AMM 32-41-15/401, Landing Gear Brake Unit
(4)
AMM 32-42-04/401, Antiskid Transducer
(5)
AMM 32-45-01/401, Main Gear Tire/Wheel Assembly
F.
Access
(1)
Location Zone
735 Wing Landing Gear, LH
745 Wing Landing Gear, RH
G.
Prepare for the Procedure
S 494-002
WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) Install the ground locks in all landing gear (AMM 09-11-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-32
ALL ú ú 01 Page 401 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
PULL BOX
SEE A
SEE C
SEE B
TOW FITTING
A A
A
Axle Sleeve Installation for the Wing Landing Gear Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-32
ALL ú ú 01 Page 402 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
THERMOMETER SENSOR
DO NOT REMOVE THE GREASE FROM THIS AREA.
APPLY BMS 3-33 GREASE TO THESE AXLE SURFACES BEFORE YOU INSTALL THE AXLE SLEEVE.
Axle Sleeve Installation for the Wing Landing gear Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-32
ALL ú ú 01 Page 403 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
HYDRAULIC
HAND PUMP
AXLE SLEEVE
HYDRAULIC RAM
TUBE ASSEMBLY
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(68)
