S 494-030

 (6)  
Put protective pads on the wheel truck below the truck positioning actuator and the torsion link.

 S 034-009

 (7)  
Disconnect the head end of the truck positioning actuator from the shock strut, and lower the actuator to the weel truck.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-02
 ALL  ú ú 01 Page 405 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 034-010
 WARNING: PUT A SUITABLE SUPPORT UNDER THE STEERING YOKE, STEERING
_______ CYLINDERS, AND TORSION LINK BEFORE YOU REMOVE THE YOKE ATTACH PIN. TOGETHER, THESE PARTS WEIGH APPROXIMATELY 437 POUNDS AND COULD CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT IF THEY ARE ALLOWED TO FALL.
 (8)  Disconnect the steering yoke from the shock strut, and lower the steering mechanism (steering yoke, steering cylinders, and torsion link) to the wheel truck.
 NOTE: You can leave this steering mechanism connected to the
____ wheel truck if you provide adequate protective pads and supports.
 S 034-011
 (9)  Remove the two brake rod bolts to disconnect the brake rods from the inner cylinder of the shock strut.
 NOTE: If it is not easy to remove the bolts, use the overhead
____ mechanical equipment to remove the weight of the brake rods.
 S 034-012
 (10)
 Disconnect the shock strut from the wheel truck.

 (a)  
Remove the pivot nut and washer from the truck pivot bolt.

 (b)  
Use the overhead mechanical equipment to remove the weight of the shock strut from the pivot bolt.

 (c)  
Remove the pivot bolt.

 S 024-013
 (11) Carefully lift the shock strut off the wheel truck with the overhead mechanical equipment.
 TASK 32-13-02-404-014
 3. Body Gear Shock Strut Installation (Fig. 401)
__________________________________
 A. Special Tools and Equipment
 (1)  
12PRE65B00161-1 - Thread Protector, Pivot Pin

 (2)  
OHME65B01201-1, Mechanical Equipment, Overhead, Wing and Body Gear

 B.
Consumable Materials

 (1)  
D00633 Grease - BMS 3-33 (preferred)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-02
 ALL  ú ú 01 Page 406 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (2)  
D00013 Grease - MIL-G-23827 (optional)

 C.
References

 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM 32-00-30/201, Landing Gear Door Locks

 (3)  
AMM 32-13-01/401, Body Landing Gear

 (4)  
AMM 32-13-03/401, Body Gear Side Brace

 (5)  
AMM 32-13-11/601, Body Gear Wheel Truck

 (6)  
AMM 32-42-20/601, Body Gear Brake Rods

 (7)  
AMM 32-13-15/601, Body Gear Truck Positioning Actuator

 (8)  
AMM 32-53-11/601, Body Gear Steering Actuator and Yoke Assembly

 D.
Access

 (1)  
Location Zone
 755 Body Landing Gear, LH
 765 Body Landing Gear, RH

 E.
Installation

 S 224-016
 (1)  
Do a check of the truck pivot attachments for wear
 (AMM 32-13-11/601).

 S 224-018

 (2)  
Do a check of the brake rod attachments for wear (AMM 32-42-20/601).

 S 224-035

 (3)  
Do a check of the steering yoke attachments for wear
 (AMM 32-53-11/601).

 S 224-036

 (4)  
Do a check of the attachments for the truck positioner actuator for wear (AMM 32-13-15/601).

 S 424-031

 (5)  
Using the mechanical equipment, carefully lower the shock strut into its position on the wheel truck.

 S 434-017

 (6)  
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(144)