BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

WING GEAR TRUNNION FORK HOUSING

A-A
OVERSIZE NUT
Reworked Wing Gear Trunnion Fork Housing
Figure 404

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-19
 ALL  ú ú 01 Page 413 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
G89244
A
747-400 MAINTENANCE MANUAL
 (c)  Install the lockbolts (9).
 S 824-051
 (5)  
Loosen the bearing adjusting ring (14) (counterclockwise).

 (a)  
Install the ring against the bearing flange with a torque value of 24 to 120 pound-inches.

 NOTE: Use the torque wrench adapter to align the slots with
____ the keyways in the trunnion outer sleeve (Fig. 402).
 S 824-052
 (6)  
Align the keyways in the trunnion outer sleeve (15) and the adjusting ring (14).

 S 434-066

 (7)  
Install the key (25) before you install the lockwasher (7) and the nut (8).

 NOTE: The recommended key configuration has a chamfer on all
____
 the corners.

 S 434-053
 (8)  
Install the lockwasher (7) and the locknut (8).

 (a)  
Tighten the locknut (8) with your hand.

 NOTE: Loosen it if it is necessary to install the
____
 lockplate (11) and the lockwire.

 (b)  Install the lockplate (11) and the lockwire.
 S 624-054
 (9)  
Apply a bead layer of corrosion preventive compound fully around the joint (Fig. 403).

 S 644-055

 (10)
 Apply a thick bead of grease around the inner race to the sleeve joint (Fig. 403).

 S 644-060

 (11)
 Lubricate the grease fitting on the bottom side of the trunnion sleeve with grease (Fig.402).

 NOTE: After an overhaul, there is BMS 3-27 grease between the
____ trunnion journal and the trunnion sleeve. The grease channel is full of grease if the BMS 3-27 does not come through the grease vent. The grease vent is on the bottom side of the trunnion sleeve.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-19
 ALL  ú ú 02 Page 414 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 I. Put the airplane back to its usual condition.
 S 094-056
 (1)  
Remove the landing gear dolly.

 S 864-057

 (2)  
Lower the airplane (AMM 07-11-01/201).

 S 094-064
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (3)  
Do this task: "Removal of the Door Locks on the Wing Landing Gear" (AMM 32-00-30/201).

 S 094-065

 (4)  
Do this task: "Removal of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-19
 ALL  ú ú 01 Page 415 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 WING GEAR TRUNNION FORK - INSPECTION/CHECK
__________________________________________
 1.  General_______
 A.  This procedure measures the fit of the housing of the trunnion fork bearing, the bushings, and the trunnion fork bolts.
 TASK 32-11-19-206-001
 2.  Trunnion Fork For Wear Check (Fig. 601)____________________________
 A.  References
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(34)