32-11-20
 ALL  ú ú 01 Page 402 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 864-028 WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (2)  Install the ground locks in all landing gear (AMM 09-11-00/201).
 S 494-029 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (3)  
Do this task: "Installation of the Door Locks on the Wing Landing Gear" (AMM 32-00-30/201).

 S 494-030

 (4)  
Do this task: "Installation of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).

 S 844-004

 (5)  
Release the pressure from the hydraulic system No. 4 (AMM 29-11-00/201).

 S 844-005 WARNING: RELEASE THE PRESSURE FROM THE ACTUATOR BEFORE YOU DISCONECT THE
_______ HYDRAULIC LINES FROM THE ACTUATOR. THIS WILL PREVENT INJURY TO PERSONS.
 (6)  
Open the bleed valve to release the pressure from the actuator. S 034-006

 (7)  
Disconnect the hydraulic line from the actuator. NOTE: Put a cap on the line and seal the port.

____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-20
 ALL  ú ú 01 Page 403 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 034-007
 (8)
Remove the bolt, two end caps, the pin and the spacers to disassemble the actuator rod end from the bellcrank.

 S 034-008

 (9)  
Remove the bolt, end caps, the pins and the spacers to disassemble the head end attachment from the shock strut.

 S 024-009

 (10)
 Remove the actuator from the airplane.

 TASK 32-11-20-404-010
 3.  Truck Positioner Actuator Installation_______________________________________
 A. Consumable Materials
 (1)  
C00272 Fluid-Hydraulic, Fire Resistant, BMS 3-11

 (2)  
D00633 Grease - BMS 3-33 (preferred)

 (3)  
D00013 Grease - MIL-G-23827 (optional)

 B.
References

 (1)  
AMM 12-12-01/301, Hydraulic Systems

 (2)  
32-00-30/201, Landing Gear Door Locks

 (3)  
AMM 32-11-20/601, Wing Gear Truck Positioning Actuator

 (4)  
AIPC 32-11-02 Fig. 2

 (5)  
AIPC 32-11-20 Fig. 1

 (6)  
AIPC 32-11-21 Fig. 1

 C.
Access

 (1)  
Location Zone
 735 Wing Landing Gear, LH
 745 Wing Landing Gear, RH

 D.
Procedure

 S 224-035
 CAUTION: MAKE SURE THAT YOU DO NOT MOVE OR DAMAGE THE WING GEAR TRUCK
_______ SENSORS OR TARGET BRACKET. IF THE TARGET BRACKET OR SENSORS ARE MOVED, THEN THE AIRPLANE SYSTEMS MAY NOT RECOGNIZE AN IN-AIR CONDITION.
 (1)  If the sensor or target bracket is moved or damaged, then do the task to measure the wing landing gear truck sensor clearance (AMM 32-61-22/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-20
 ALL  ú ú 01 Page 404 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (2)  S 224-013Examine the attached points for too much worn areas (AMM 32-11-20/601).
 (3)  S 424-014Put the actuator with the head end to the shock strut.
 (4)  S 434-015Align the spherical bearing with the shock strut lugs. (a) Install the pin and the spacers between the shock strut lugs and the actuator bearing.
 (5)  S 644-016Lubricate the shank and the thread of the bolt that attach the actuator head end to the shock strut.
 (6)  S 434-017Add two end caps, the bolt, the flat washer, and the nut. (a) Tighten the nut and install the cotter pin.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(37)