S 865-004

 (5)  
Remove the pressure from hydraulic systems No. 1 and 4
 (AMM 29-11-00/201).

 G.
Adjust the inboard door for the wheel well (Fig. 502 and 503)

 NOTE: You must remove the outboard door (AMM 32-12-01/401) if you
____ install the outboard door before the adjustment of the inboard door. You must follow the adjustment procedures to make sure the door actuator lock is fully in the door closed position.
 S 825-200
 (1)  Table 501 (for Figures 502 & 503) shows expanded tolerances which were permitted at delivery. Use these tolerances only if you can not get the usual tolerances.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-00
 ALL  ú ú 01 Page 503 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 ~...............................................................................
 |  WING GEAR WHEEL WELL DOOR FLUSHNESS AND CLEARANCE DEVIATIONS  |
 |  INBOARD DOOR  |
 |  TABLE 501  |

 ................................................................................. | | | TYPE OF | MISMATCH | | | AIRPLANE | ZONE | MISMATCH | (FLUSHNESS) | CLEARANCE | 2............…........….............…..................…........................1
 S 015-005
 (2)  
If it is necessary, remove the outboard door (AMM 32-12-01/401).

 S 835-006

 (3)  
Adjust the inboard door:

 CAUTION: IF YOU MOVE THE DOOR WITH THE VALVE LINKAGE CONNECTED AND
_______ INCORRECTLY ADJUSTED OR THE VALVE RIGGING PIN NOT REMOVED, YOU CAN CAUSE DAMAGE TO THE VALVE MECHANISM.
 (a)  
Disconnect the linkage rod of the sequence valve from the rod end fitting at point B (View A, Fig. 502).

 (b)  
Put the serrated bracket (View B, Fig. 502) on the inboard door with bolts in the center of the slots.

 (c)  
Tighten the fasteners.

 NOTE: If the outboard door is not removed, extend the length
____ of the two radius rods. This produces an "out-of-fair" condition on the outboard door of 0.10-inch minimum outside the airplane contour.
 (d)  
Remove the bolt for the forward door stop, the shim and the stop plate (View E-E, Fig. 503).

 (e)  
Disconnect the linkage rod of the inboard door from the door (Fig. 502).

 (f)  
Hold the loose end of the actuator linkage rod until no damage will occur when the door is closed in the subsequent steps.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-00
 ALL  ú ú 31 Page 504 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

Wing Gear Doors Locations
Figure 501

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-00
 ALL  ú ú 02 Page 505 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

SEE  A 
OUTBOARD DOOR RADIUS ROD 
OUTBOARD DOOR RADIUS ROD  STRIKE BOARD 
FWD INBD  DOOR ACTUATOR WING GEAR WHEEL WELL INBOARD DOOR  A A  INBOARD DOOR LINKAGE ROD  OUTBOARD DOOR WING GEAR WHEEL WELL 

INBOARD DOOR
KEEL BEAM LINKAGE ROD
(REF) OUTBOARD DOOR
SERRATED RADIUS ROD
BRACKET SEE C SEE B WING GEAR
WING GEARWHEEL WELL WHEEL WELLINBOARD DOOR OUTBOARD DOOR
INBD
A-A
Wing Gear Wheel Well Door Adjustment
Figure 502 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(76)