曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 NOTE:____ The electrical heat blanket and the dry ice will help with the movement of the sleeve.
 (7)  S 434-026Install the retention pin for the axle sleeve: (a) Apply the BMS 10-11 primer to the area in the retention pin hole of the axle. (b) Install the retention pin while the primer is wet. 1) Lightly push the retention pin into the axle. 2) Make sure the retention pin fully engages with the axle.
 (8)  S 644-027Fill the bushing flange slot at the truck beam with grease (Fig. 401).
 (9)  S 884-028Apply thermal loads to the axle and the brake housing bushing.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-32
 ALL  ú ú 01 Page 411 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 WARNING:_______DO NOT GET THE DRY ICE ON YOUR SKIN. THE DRY ICE IS FROZEN CARBON DIOXIDE AT A TEMPERATURE OF APPROXIMATELY -120°F. THE COLD TEMPERATURE OF THE CARBON DIOXIDE CAN CAUSE INJURY TO PERSONS.
 (a)  Decrease the temperature of the axle with the dry ice.
 1)  Apply the dry ice to the inner diameter and the outer diameter of the axle.
 NOTE: When the steam from the dry ice almost stops, the
____ axle temperature will be near the temperature of the dry ice (-120°F). This is the recommended condition.
 2)  Add more dry ice to the inner diameter of the axle to keep the axle at a constant temperature.
 (b)  Put the electrical heat blanket around the brake housing bushing (Fig. 401, View B).
 CAUTION: DO NOT PERMIT THE TEMPERATURE OF THE AXLE COMPONENTS TO
_______ BECOME 300°F FOR MORE THAN 180 MINUTES. THE MATERIALS FOR THE AXLE COMPONENTS CAN BECOME WEAK IF THE THERMAL LOADS ARE TOO LARGE. WEAK AXLE COMPONENTS CAN HAVE A FAILURE DURING OPERATION.
 (c)  Permit the temperature of the brake housing bushing to become approximately 250°F. 1) Use the thermometer to measure the temperature of the brake
 housing bushing.
 S 094-029
 (10)
 Remove the electrical heat blanket from the brake housing bushing.

 S 434-030

 (11)
 Immediately install the brake housing bushing before the temperatures of the bushing and the axle go to the ambient temperature.

 CAUTION:_______DO NOT HIT THE BUSHING DIRECTLY WITH THE HAMMER. THIS WILL CAUSE DAMAGE TO THE BRAKE HOUSING BUSHING.
 (a)  
If it is necessary, carefully use a hammer with a block of wood to move the sleeve.

 (b)  
Make sure the flange of the brake housing bushing is fully against the truck beam.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-32
 ALL  ú ú 01 Page 412 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 644-031
 (12)
 Fill the retention pin hole with grease until the grease is smooth with the surface of the axle sleeve.

 S 094-032

 (13)
 Remove the cloth from the inner diameter of the axle at the location where the axle engages with the truck beam.

 NOTE: This cloth supplied protection for the components in the
____ other end of the axle during the removal task.
 S 164-033
 (14)
 Remove all signs of the dry ice from the inner diameter of the axle.

 S 434-034

 (15)
 Push the transducer wires into the axle from the pull box at the tow fitting.

 S 434-035

 (16)
 Install the brake unit (AMM 32-41-15/401).

 S 434-036

 (17)
 Install the antiskid transducer (AMM 32-42-04/401).

 S 434-038

 (18)
 Install the tire/wheel assembly (AMM 32-45-01/401).

 H.
Put the Airplane in Its Usual Condition

 S 094-039
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASKS BELOW TO REMOVE
_______ THE DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (1)  
Do this task: "Removal of the Door Locks from the Wing Landing Gear" (AMM 32-00-30/201).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(72)