曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

____
 (b)  Use the solvent to clean the area on the truck where you will install clamp B.
 NOTE: Use a clean dry cloth to wipe the truck dry.
____
 1)  Apply aluminized epoxy primer with a brush to the area on the truck which will contact clamp B, except the area that is covered by the bumper plate.
 (c)  Install three wraps of tape around the truck beam where clamp B will be installed.
 NOTE: Make an approximately 1-inch overlap on the ends of the
____
 tape.

 (d)  Install the bumper on clamp B with four bolts, four washers, and four nuts.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-26
 ALL  ú ú 01 Page 405 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (e)  
Apply sealant with a brush to the area on the truck which will contact the bumper plate immediately before you install the clamp B.

 (f)  
Install clamp B on the truck as shown (Fig. 402).

 NOTE: Make sure the downward slope of the bumper is facing
____
 forward.

 1)  Make sure the bumper is at the correct distance from the end of the truck beam (View A, Fig. 402).
 2)  Make sure that the centerline of the bumper and the centerline of the truck align within 0.10 inch (View A-A, Fig. 402).
 (g)  Make sure the bumper plate-to-truck beam dimension is 0.36 inch or less (View B, Fig. 402): 1) Loosen or remove the 4 nuts that attach the bumper to the
 bumper plate. 2) Put the T-bolt trunnion as near to the bumper pad as possible. 3) Apply a vertical force down on the top of the bumper of
 approximately 100 pounds. 4) Tighten clamp B while you apply the vertical force. 5) Remove the force and examine the dimension limit as shown. 6) Tighten the four nuts.
 S 094-034
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (3)  
Do this task: "Removal of the Door Locks on the Wing Landing Gear" (AMM 32-00-30/201).

 S 094-033

 (4)  
Do this task: "Removal of the Door Locks on the Body Landing Gear" (AMM 32-00-30/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-26
 ALL  ú ú 01 Page 406 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE A
15.48
INCHES
15.38
SEEB A
A
CLAMP A CLAMP B
A
Bumper Installation for the Wing Landing Gear
Figure 402 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-26
 ALL  ú ú 01 Page 407 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 

CENTERLINE OF BUMPER AND CENTERLINE OF TRUCK MUST ALIGN WITHIN 0.10 INCHES
Bumper Installation for the Wing Landing Gear Figure 402 (Sheet 2)
H12926
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-26
 ALL  ú ú 01 Page 408 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 WING GEAR SIDE STRUT COMPONENT ASSEMBLY - REMOVAL/INSTALLATION
______________________________________________________________
 1.  General_______
 A.  The procedure has two tasks:
 (1)
The removal of the side strut component for the wing landing gear.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(57)