曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 434-009
 (2)  Make sure you install the bushings in the forward hinge support and the aft hinge support.
 NOTE: The flanged of the aft hinge bushing should be on the inner
____ side of the aft hinge support when you install (Detail C, Fig. 401).
 D.  Procedure
 S 424-010
 (1)  
Install the outboard door of the shock strut.

 (a)  
Put the door in its position for installation.

 (b)  
Install the hinge bolts (Details B and C, Fig. 401). 1) Tighten the forward hinge nut 370 - 610 pound-inches. 2) Tighten the aft hinge nut 1000 - 1300 pound-inches.

 (c)  
Clean and install the bonding jumpers.

 (d)  
Connect the linkage rod to the outboard door.

 1)  If you replace or change the length the linkage rod, adjust the rod to 23.50 inches from the center of each rod.

 (e)  
Tighten the nut 290 - 410 pound-inches (Detail A, Fig. 401).

 S 834-011
 (2)  
Adjust the outboard door of the shock strut on the wing landing gear (Ref 32-12-00/501).

 S 414-012

 (3)  
Install the inboard door of the shock strut on the wing landing gear (Ref 32-12-06/401).

 S 094-016
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO REMOVE THE
_______ DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (4)  Do this task: "Removal of the Door Locks from the Wing Landing Gear" (Ref 32-00-30/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-07
 ALL  ú ú 01 Page 405 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 094-017
 (5)  Do this task: "Removal of the Door Locks from the Body Landing Gear" (Ref 32-00-30/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-12-07
 ALL  ú ú 01 Page 406 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 WING LANDING GEAR SHOCK STRUT OUTBOARD DOOR - INSPECTION/CHECK
______________________________________________________________
 1.  General
_______
 A.  This procedure contains a task to examine the outboard door of the shock strut on the wing landing gear for worn parts. The parts to examine includes the attach fitting and the hinge assemblies of the outboard door.
 B.  To do this procedure, you must remove the outboard door of the shock strut on the wing landing gear.
 TASK 32-12-07-206-001
 2.  The Wing Gear Shock Strut Outboard Door Inspection (Fig. 601)
__________________________________________________
 A.  References
 (1)  
AMM 32-12-06/401, Wing Gear Shock Strut Inboard Door

 (2)  
AMM 32-12-07/401, Wing Gear Shock Strut Outboard Door

 (3)  
AIPC 32-12-05 Fig. 1

 (4)  
AIPC 32-12-06 Fig 1

 (5)  
AIPC 32-12-07 Fig 1

 B.  
Access

 (1)  
Location Zone
 733 Wing Landing Gear Door, LH
 743 Wing Landing Gear Door, RH

 C.  
Procedure

 S 866-008
 (1)  
Do this task: "Wing Landing Gear Shock Strut Outboard Door Removal" (AMM 32-12-07/401).

 S 866-009

 (2)  
Do this task: "Wing Landing Gear Shock Strut Inboard Door Removal" (AMM 32-12-06/401).

 S 226-005

 (3)  
Examine the components on the outboard door of the shock strut for worn areas.

 (a)  
Measure the parts at the locations shown in Figure 601.

 (b)  
Compare the measured dimensions to the wear limits in Figure 601.

 (c)  
If a part is not in tolerance, replace the part if you cannot repair it.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 2(113)