c Use a SPATULA - WOODEN to apply a layer of the adhesive of
_
the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) or
the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004A) to the seal.
d Make sure that air bubbles do not show. Air bubbles are not
_
permitted.
e Put the seal in position and align the holes in the seal
_ with the pre-drilled holes in the panel.
NOTE : You must install the seal on the panel in less than
____ ten minutes from when you applied the adhesive.
(g)
Install the new seal with the rivets (Ref. ASRM 514200).
(h)
Make sure that the new rivets are flush with the fairing skin and a protective coating is applied.
(4) Make sure that the work area is clean and clear of tool(s) and other items.
**ON A/C 002-049, 051-051, 053-099, 101-105, 151-199, 201-214,
Subtask 53-35-13-350-050
B. Replacement of the Bonded Seals of the Panels 197GB (198GB)
(Ref. Fig. 404/TASK 53-35-13-991-010)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : DO NOT GET THE PAINT ON YOUR SKIN OR IN YOUR EYES. PUT ON
_______ PROTECTIVE CLOTHING, GOGGLES AND A FACE MASK. USE THE PAINT IN A WELL VENTILATED AREA. IF IN A CONFINED AREA, USE A SUPPLIED AIR RESPIRATOR. DO NOT BREATHE THE GAS. GET MEDICAL AID IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Remove the rivets (2) and the dimpled washers (4) from the panel (3) (Ref. ASRM 514200).
R EFF : 002-049, 051-051, 053-099, 101-105, 53-35-13Page 421 151-199, 201-214, 401-499, Aug 01/05
CES
Bonded Seal Replacement - Panel 197GB (198GB) Figure 404/TASK 53-35-13-991-010
R EFF : 002-049, 051-051, 053-099, 101-105, 151-199, 201-214, 53-35-13 Page 422 May 01/05
CES
(2)
Remove and discard the defective seal (1) from the panel (3).
(3)
Clean the panel.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES AND A MASK.
(a) Clean the panel (3) with a lint-free cotton cloth, MISCELLANEOUS (Material No. 19-003) and the CLEANING AGENTS (Material No. 11-003), to remove the remaining adhesive.
(4)
Put the new seal (1) in its correct position at the edge of the panel (3).
(5)
Cut the seal (1) to its correct length, and if necessary, cut the
edge of the seal (1) as shown, do this until the shape agrees with
the curve of the panel (3).
(6)
Hold the seal (1) in position and put marks on it to align with the rivet holes in the panel (3).
(7)
Remove the seal (1) and make the holes for the rivets (2).
(8)
Make the surface of the panel (3) rough with the emery cloth, grade
400.
NOTE : Be careful that you do not damage the surface of the panel
____
(3).
(9) Lightly rub the mating surface of the seal (1) with the emery cloth, grade 120 to 240.
(10) Clean the components.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES AND A MASK.
(a) Clean the mating surfaces of the seal (1) and the panel (3) with a lint-free cotton cloth, MISCELLANEOUS (Material No. 19-003) and the CLEANING AGENTS (Material No. 11-003).
(11) You can use for the bonding of the seal (1) the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-033), the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) or the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004A).
R EFF : 002-049, 051-051, 053-099, 101-105, 53-35-13Page 423 151-199, 201-214, May 01/05
CES
(a)
When you use the BONDING AND ADHESIVE COMPOUNDS (Material No. 08-033):
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM FUSELAGE 機(jī)身2(124)
