Upper Corners of the Cutout and Sealing Profile at the BULK Cargo-Compartment
Door
Figure 607/TASK 53-41-00-991-010
CES
(3)
If necessary, make the surface of the inspection area smooth with the abrasive cloth, grade 280.
(4)
Make sure the inspection area is clean and dry before you continue.
(5)
Do a visual inspection of the surface of the inspection area. Look for damage, and defects in the shape of the surface.
(6)
If you find damage :
(a)
Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.
(b)
If you find corrosion damage:
-
refer to the ASRM (Ref. ASRM 51-22-00-001) for the general corrosion data
-
refer to the ASRM (Ref. ASRM 51-74-00-001) for the repair of the corroded areas.
(c)
If you find other types of damage:
-refer to the ASRM (Ref. ASRM 53-41-11-101) for the necessary data.
4. Procedure
_________
(Ref. Fig. 607/TASK 53-41-00-991-010)
Subtask 53-41-00-210-064
A. Special Detailed Inspection Procedure
(1) Do the special detailed inspection of the fuselage skin at the cutout for the bulk cargo door. Do this at the forward and aft upper corners of the cutout (Ref. NTM 534171-Part.6).
NOTE : If the inspection areas are painted , before you do the
____
inspection you must:
-refer to the procedure steps in the NTM (Ref. NTM 534171-Part.6), 'Preparation for Inspection'
-measure the thickness of the paint at the inspection areas
-make sure that the paint thickness is less than the given limit.
(2) Write a report about the damage you find during the inspection procedure.
R EFF : 001-049, 051-099, 101-149, 221-221, 53-41-00Page 632 224-224, 228-228, May 01/05
CES
(3) If you find damage:
(a)
Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.
(b)
If you find corrosion damage:
-
refer to the ASRM (Ref. ASRM 51-22-00-001) for the general corrosion data
-
refer to the ASRM (Ref. ASRM 51-74-00-001) for the repair of the corroded areas.
(c)
If you find other types of damage:
-refer to the ASRM (Ref. ASRM 53-41-11-101) for the necessary data.
5. Close-up
________ Subtask 53-41-00-370-059
A. Repair of the Surface Protection
(1) If necessary, repair the paint coatings in the inspection areas (Ref. TASK 51-75-12-300-003) or (Ref. TASK 51-75-12-300-001).
Subtask 53-41-00-410-077
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the BULK cargo-compartment door (Ref. TASK 52-30-00-860-008).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R EFF : 001-049, 051-099, 101-149, 221-221, 53-41-00Page 633 224-224, 228-228, May 01/05
CES **ON A/C ALL
TASK 53-41-00-210-009
Detailed Visual Inspection of Lower Skin of Longitudinal Lap Joints in Crack Stopper Areas at Stringer 32 LH between FR47 and FR53, External Surface
1. Reason for the Job
__________________
Refer to the MPD TASK: 534116-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific lint-free cloth
B. Consumable Materials
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身2(142)
