3. Job Set-up
__________
Subtask 53-21-00-010-070
A. Get Access
(1)
Put an access platform in position at the zone 825.
(2)
Open the forward cargo-compartment door 825 (Ref. TASK 52-30-00-860-001).
R **ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
Subtask 53-21-00-010-054
B. Removal of the Components
(1)
Remove the ceiling panel 131AC (Ref. TASK 25-54-12-000-002).
(2)
Remove the floor panels 132GF, 132FF (Ref. TASK 53-22-14-000-001).
EFF : ALL
53-21-00Page 691
(3)
Remove the sidewall panel 132KW (Ref. TASK 25-54-12-000-003).
(4)
Remove the partition panels 132BW, 132EW.
(5)
Remove the insulation blankets at the location of the removed panels (Ref. TASK 25-80-00-000-001).
R **ON A/C 151-199, 401-499,
Subtask 53-21-00-010-054-A
B. Removal of the Components
(1)
Remove the ceiling panels 131MC, 131PC (Ref. TASK 25-54-12-000-002).
(2)
Remove the floor panels 132GF, 132FF (Ref. TASK 53-22-14-000-001).
(3)
Remove the sidewall panel 132KW (Ref. TASK 25-54-12-000-003).
(4)
Remove the partition panels 132BW, 132EW.
(5)
Remove the insulation blankets at the location of the removed panels (Ref. TASK 25-80-00-000-001).
**ON A/C ALL
Subtask 53-21-00-110-067
C. Cleaning of the Structure WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Clean the inspection area with CLEANING AGENTS (Material No. 11-004) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003), if necessary.
EFF : ALL
53-21-00Page 692
4. Procedure
_________
Subtask 53-21-00-220-066
A. Inspection
(1)
Do a detailed inspection of the internal structure around the forward cargo-door cutout. This inspection is applicable from FR24 to FR29 and between STGR23 and STGR38, right side.
(2)
Make sure that there is no :
(a)
Corrosion damage :
-If you find corrosion damage, refer to the Structural Repair Manual (Ref. SRM 512200 P.Block 001) for types of corrosion, inspection, removal and corrosion protection.
(b)
Other damage (cracks, scratches, stress, marks, dents, bumps,..) :
-If you find this type of damage, refer to the Structural Repair Manual (Ref. SRM 511100 P.Block 001) for damage classification and corrective action.
Subtask 53-21-00-916-051
B. Application of Temporary Protection
CAUTION : DO NOT APPLY TEMPORARY PROTECTION ON THE OXYGEN SYSTEMS.
_______ MAKE SURE THAT THE TEMPORARY PROTECTION DOES NOT GET: -ON COMPOSITE PARTS, CONTROL CABLES, PULLEYS,TEFLON BEARINGS. -ON LUBRICATED SURFACES. -IN DRAIN VALVES OR OTHER ORIFICES. TEMPORARY PROTECTION ON OR IN THESE PARTS CAN CAUSE DAMAGE.
(1)
Apply masking tape or masking tape BONDING AND ADHESIVE COMPOUNDS (Material No. 08-074) on the equipment and fittings adjacent to the area.
(2)
Apply a layer of STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-006) to the inspection area.
(3)
Remove the masking paper or the masking tape.
EFF : ALL
53-21-00Page 693
May 01/05
R
CES 5. Close-up
________
**ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
Subtask 53-21-00-410-054
A. Installation of the Components
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the insulation blankets (Ref. TASK 25-80-00-400-001).
(3)
Install the partition panels 132BW, 132EW.
(4)
Install the sidewall panel 132KW (Ref. TASK 25-54-12-400-003).
(5)
Install the floor panels 132GF, 132FF (Ref. TASK 53-22-14-400-001).
(6) Install the ceiling panel 131AC (Ref. TASK 25-54-12-400-002). R **ON A/C 151-199, 401-499,
Subtask 53-21-00-410-054-A
A. Installation of the Components
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUSELAGE 機身2
