WALL THICKNESS (INCH)
DESIGN AFTER REWORK MINIMUM
0.120 0.100 0.083 0.075 0.108 0.090
Flap Torque Tube Repairs
Figure 801
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-64
ALL ú ú 01 Page 801 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
D. Procedure
S 028-002
(1)
Remove the flap torque tube (Ref 27-51-64/401).
S 168-003
(2)
Clean the torque tube.
S 218-004
(3)
Examine the torque tube for worn areas and areas where the wall thickness is decreased.
S 358-005
(4)
Repair all defects in the torque tube:
(a)
Use a minimum blend radius of 1.00 inch on the repaired area.
(b)
Make sure the surface finish of the repaired area is 63-microinches or better.
(c)
Make sure the wall thickness is in the limits shown in the table.
(d)
Apply the colored alodized surface treatment to the area.
(e)
Apply an abrasion-resistant teflon finish to the repaired area and to each side of the repaired area (Ref 51-21-81/701).
(5)
Install the torque tube (Ref 27-51-64/401).
S 428-006
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-64
ALL ú ú 01 Page 802 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
FLAP RIGHT ANGLE GEARBOX - REMOVAL/INSTALLATION
_______________________________________________
1. General
_______
A. There are two tasks in this procedure. There is a procedure for the removal and a task for the installation of the flap right angle gearbox.
TASK 27-51-67-004-001
2. Flap Right Angle Gearbox Removal (Fig. 401)
________________________________
A. References
(1)
27-51-00/201, Trailing Edge Flap System
(2)
27-51-32/401, Inboard Flap Track Fairings
B.
Access
(1)
Location Zone
216, 217 Main Wheel Well
C.
Procedure
S 014-002
(1)
Remove the inboard flap track fairing (Ref 27-51-32/401).
S 864-003
(2)
Supply hydraulic system B power (Ref 27-51-00/201).
S 864-004
(3)
Put the flap control lever in the UP detent to retract the flaps.
NOTE: The flaps must be in the fully retracted position to align
____
the bolt holes.
S 864-005
(4)
Remove the hydraulic system B power (Ref 27-51-00/201).
S 034-006
(5)
Disconnect the flap torque tubes from the gearbox:
(a)
Install a support to hold the flaps while the torque tubes are disconnected.
(b)
Remove the screws that attach the coupling sleeves to the gearbox coupling.
(c)
Move the sleeves off the couplings to disconnect the torque tubes.
S 024-007
(6)
Remove the right angle gearbox:
(a)
Remove the three mounting bolts that attach the support bracket to the structure.
(b)
Remove the three housing bolts that attach the gearbox to the support bracket.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-67
ALL ú ú 01 Page 401 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
TORQUE TUBE
RIGHT GEARBOX SHOWN (LEFT GEARBOX EQUIVALENT)
THE HEAD OF THE BOLT MUST POINT FORWARD.
Flap Right Angle Gearbox Installation Figure 401 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(100)
