27-51-74
 ALL  ú ú 01 Page 506 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500
MAINTENANCE MANUAL

SEE A
DOWNSTOP ASSEMBLY
FLAP TRANSMISSION DOWNSTOP
UPSTOP
JACKSCREW BALLSCREW NUT
UPSTOP
SEE B

(EXAMPLE) FWD A
UPSTOP (SCREW YOKE)
UPSTOP (BALLSCREW NUT)
DIMENSION "X"
B
Flap Transmission Upstop Clearance
Figure 503

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-74
 ALL  ú ú 01 Page 507 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 7)  Stop for two minutes, then do this task: "Hydraulic System
 B Depressurization" (AMM 27-51-00/201). 8) Make sure that you can install the rig pin F-1 freely. 9) If you cannot install the rig pin freely, do the cam link
 adjustment again. 10) Tighten the checknuts and install the lockwire. 11) Make sure the threads engage in the limits shown.
 (n)  
Remove the rig pin F-1.

 (o)  
Do this task: "Hydraulic System B Pressurization"
 (AMM 27-51-00/201).

 (p)  
Extend and retract the flaps five times: 1) Put the flap control lever in the 40-unit detent to extend the flaps.

 2)  Put the flap control unit in the UP detent to retract the flaps.

 (q)  
Stop for two minutes, then do this task: "Hydraulic System B Depressurization" (AMM 27-51-00/201).

 (r)  
Make sure that you can install the rig pin F-1 freely in the flap control unit.

 (s)  
If you cannot install the rig pin freely, adjust the cam link for the trailing edge flaps again.

 S 415-024
 (3)  
Install the lower pan on the flap control unit.

 S 825-004

 (4)  
Use the wrench set to adjust the flap limit switches:

 (a)  
Do this task: "Mach Trim Flap Switch" (AMM 22-21-31/501).

 (b)  
Do this task: "Flap Limit Switch Adjustment"
 (AMM 27-51-87/501).

 (c)  
Do this task: "Flaps 10 degree Switch Adjustment"
 (AMM 27-88-21/501).

 (d)  
Do this task: "Stall Warning Switch Installation"
 (AMM 27-88-31/401).

 (e)  
Do this task: "Flap Landing Warning Switch Installation" (AMM 31-26-12/401).

 (f)  
Do this task: "Flap Takeoff Warning Switch Installaiton" (AMM 31-26-23/401).

 S 415-005
 (5)  
Install the limit switch cover:

 (a)  
Apply a layer of the grease on the cover.

 (b)  
Install the cover on the flap control unit.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-74
 ALL  ú ú 01 Page 508 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 725-006
 (6)  Do this task: "Flap Control Unit Functional Test"
 (Ref Paragraph 3).

 TASK 27-51-74-725-007
 3.  Flap Control Unit Functional Test_________________________________
 A. References
 (1)  
AMM 22-21-31/501, Mach Trim Flap Switch

 (2)  
AMM 27-51-00/201, Trailing Edge Flap Systems

 (3)  
AMM 27-88-21/501, Flaps 10-Degree Switch

 (4)  
AMM 27-88-31/401, Stall Warning Switch

 (5)  
AMM 31-26-23/401, Flap Takeoff Warning Switch

 (6)  
AMM 31-26-12/401, Flap Landing Warning Switch

 B.
Access

 (1)  
Location Zone
 217 Right Main Wheel Well

 C.
Procedure

 S 865-008
 (1)  
Do this task: "Hydraulic System B Pressurization"
 (AMM 27-51-00/201).

 S 865-009

 (2)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(132)