(a)  
Remove the rig pins F-5 and F-6.

 (b)  
Remove the bolt to disconnect the boom from the structure.

 (c)  
Loosen the cable adjustment nuts and disconnect the cables from the boom cable fittings.

 (d)  
Move the boom aft, off the boom roller.

 TASK 27-51-19-404-009
 2.  Aftflap Actuating Mechanism Boom Installation_____________________________________________
 A. Special Tools and Equipment
 (1)  Rig Pins (F-5 and F-6) - 0.248 +0.000/-0.002 inch diameter, 3.7 |0.25-inches long (MS20392-3)
 NOTE: The Rig pins are a part of the kit F70207-69, -78, or -83.
____
 B. Standard Tools and Equipment
 (1)  
Protective cover for the aftflap support

 (2)  
Support to hold the aftflap (with the protective cover)

 C.
Consumable Materials

 (1)  
D00633 Grease - BMS 3-33 (Recommended)

 (2)  
D00013 Grease - MIL-G-23827 (Alternate)

 D.
References

 (1)  
AMM 27-51-00/201, Trailing Edge Flap Systems

 (2)  
AMM 27-51-32/401, Inboard Flap Track Fairings

 E.
Access

 (1)  
Location Zone 309, 409 Wing Trailing Edge Flap and Spoilers

 (2)  
Access Panel 8403, 8503 Aft Flap Clutch and Drive Mechanism Access Panel

 F.
Procedure

 (1)  
Do this task: Hydraulic System B Pressurization (AMM 27-51-00/201).

 S 864-011

 (2)  
Put the flap control lever in the 40-unit detent to extend the trailing edge flaps.

 S 864-012
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-19
 ALL  ú ú 01 Page 405 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 
737-300/400/500MAINTENANCE MANUAL
 S 864-010
 (3)  Do this task: Hydraulic System B Depressurization
 (AMM 27-51-00/201).
 S 424-013
 (4)  Install the aftflap mechanism boom (Fig. 401):
 (a) Disconnect the two rods from the inboard aftflap.
 (b) Disconnect the forward end of the boom assembly.
 (c) Put the boom in a position to the rear of the boom roller.
 (d) Move the boom forward on the boom roller.
 NOTE: Retract the flaps if it is necessary until you can move____
 the boom forward.
 S 434-014
 (5)  Install the boom cables:
 (a) Make sure the boom cables are in the correct position on the
 pulleys.
 (b) Make sure the cable ends are connected to the boom cable
 sockets.
 (c) Install the rig pins F-5 and F-6 through the boom from the
 outboard side to hold the boom roller between the pins.
 (d) Tighten the cable adjustment nuts until the cables are not
 loose.
 (e) Remove the access panel 8403 or 8503 from the forward half of
 the lower surface of the midflap.
 S 824-015
 (6)  Adjust the boom cables:
 (a) Tighten the cable adjustment nuts until the cam roller is 0.42
 |0.03 inch from the forward end of the cam slot in the cable
 drum.
 1) If it is not easy to get the 0.42-inch dimension, you can
 use a rigging block.
 a) You can make the rigging block from a 2.25 inch plastic
 (or equivalent) block. The block must have the correct
 shape of the cam slot.
 2) Use the tape to hold the rigging block in the cam slot and
 put the roller against the block.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-19
 ALL  ú ú 01 Page 406 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  Keep the 0.42-inch dimension and adjust the adjustment nuts to
 get a cable tension of 100 |10 pounds.
 NOTE:____ The temperature must be approximately 70°F when you
 adjust the tension.  If the temperature decreases, you
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(21)