27-51-34
 ALL  ú ú 01 Page 802 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500MAINTENANCE MANUAL
FOREFLAP
FOREFLAP PUSHROD
SHEAR RIVET
EXHAUST GATE
(AIRPLANES WITH TWO PUSHRODS) B
FOREFLAP
FOREFLAP PUSHROD
SHEAR RIVET EXHAUST GATE
(AIRPLANES WITH THREE PUSHRODS) B
Outboard Flap Exhaust Gate Pushrods Repairs Figure 801 (Sheet 2)
EXHAUST GATE PUSHROD
MECHANISM PUSHROD
SHEAR RIVETS
(2 LOCATIONS)

EXHAUST GATE PUSHROD
K29806
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-34
 ALL  ú ú 01 Page 803 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 OUTBOARD TRAILING EDGE FLAP EXHAUST GATE - REMOVAL/INSTALLATION
_______________________________________________________________
 1.  General_______
 A.  There are two tasks in this procedure: There is a task for the removal and a task for the installation of the outboard trailing edge flap exhaust gate.
 TASK 27-51-35-004-001
 2.  Outboard Trailing Edge Flap Exhaust Gate Removal (Fig. 401)________________________________________________
 A.  References
 (1)  
AMM 27-51-00/201, Trailing Edge Flap Systems

 B.  
Access

 (1)  
Location Zone 101, 102 Control Cabin 307, 407 Wing Trailing Edge Outboard Flap and Spoilers

 C.  
Prepare for the Removal

 S 864-002
 (1)
Do this task: "Supply Hydraulic Power" (AMM 27-51-00/201).

 S 864-003

 (2)  
Put the flap control lever in the 40-unit detent to extend the flaps.

 S 864-006

 (3)
Do this task: "Remove Hydraulic Power" (AMM 27-51-00/201).

 D.  
Remove the Outboard Trailing Edge Flap Exhaust Gate

 S 014-036
 WARNING:_______MAKE SURE YOU HOLD THE EXHAUST GATE IN ITS POSITION. THE EXHAUST GATE CAN FALL TO THE FULL EXTEND POSITION. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (1)  
AIRPLANES WITH THREE PUSHRODS; Disconnect the exhaust gate rod assembly from the exhaust gate:

 (a)  
Remove the cotter pin, nut, washer and bolt from the exhaust gate rod assembly.

 S 014-037
 (2)  
AIRPLANES WITH TWO PUSHRODS; Disconnect the exhaust gate rod assembly from the exhaust gate:

 (a)  
Remove the nut, washer and bolt from the exhaust gate rod assembly.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-35
 ALL  ú ú 01 Page 401 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500
MAINTENANCE MANUAL

SEE A
SEE A
MIDFLAP 
AFTFLAP 
FWD
EXHAUST GATE MECHANISM  SEE B EXHAUST GATE  FOREFLAP A (RIGHT FLAP OPPOSITE) LEFT FLAP  INBD 
Outboard Flap Exhaust Gate Installation Figure 401 (Sheet 1) 

H48695
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-35
 ALL  ú ú 01 Page 402 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 024-040
 (3)  
AIRPLANES WITH THREE PUSHRODS;
 Disconnect the exhaust gate assembly from the midflap:

 (a)  
Remove the exhaust gate mounting bolts, washers, nuts and cotter pins.

 S 024-041
 (4)  
AIRPLANES WITH TWO PUSHRODS;
 Disconnect the exhaust gate assembly from the midflap:

 (a)  
Remove the exhaust gate mounting bolts, washers, and nuts.

 S 024-056
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(56)