27-51-67
 ALL  ú ú 01 Page 402 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 TASK 27-51-67-404-008
 3.  Flap Right Angle Gearbox Installation
_____________________________________
 A.  Special Tools and Equipment
 (1)  
F80186-10 TE Wing Flap Drive Installation Alignment Tool

 B.  
Consumable Materials

 (1)  
D00633 Grease BMS 3-33 (Recommended)

 (2)  
D00013 Grease MIL-G-23827 (Alternate)

 C.  
References

 (1)  
27-51-00/201, Trailing Edge Flap System

 (2)  
27-51-32/401, Inboard Flap Track Fairings

 D.  
Access

 (1)  
Location Zone
 216, 217 Main Wheel Well

 E.  
Procedure

 S 024-009
 (1)  Install the right angle gearbox on the support bracket (Fig. 401):
 CAUTION: MAKE SURE THAT THE HEAD OF THE RIGHT HOUSING BOLT IS
_______ FORWARD. THE BOLT CAN CAUSE DAMAGE TO THE RETENTION SCREWS FOR THE TORQUE TUBE COUPLING SLEEVE IF YOU INSTALL IT INCORRECTLY.
 (a)  Install the three housing bolts, washers and nuts to attach the gearbox to the support bracket. 1) Install the head of the right bolt forward. 2) Install the heads of the countersunk bolts aft.
 S 024-010
 (2)  Attach the support bracket, with the gearbox, to the structure with the three mounting bolts, washers and nuts.
 NOTE: Make sure the flaps are fully retracted.
____
 S 284-018
 (3)  Make sure the right angle gearbox and the No. 4 or 5 transmission gearbox are aligned (Fig./402):
 NOTE: The airplane must be on its landing gear when you examine the
____
 alignment.

 (a)  Install the alignment tool:
 1)  Install the alignment tool on the output shaft of the right angle gearbox and the input shaft of the transmission.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-67
 ALL  ú ú 02 Page 403 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
BOLT NO. 1
BOLT NO. 2
ALIGNMENT TOOL
END CAP
SPRING
TRANSMISSION BOLT NO. 3
GEARBOXOUTPUT SHAFT
RIGHT ANGLE
GEARBOX

INPUT SHAFT
ALIGNMENT TOOL INSTALLATION (END CAP ON TRANSMISSION)
END CAP INBD FWD
ALIGNMENT TOOL
RIGHT ANGLE
GEARBOX
SPRING

TRANSMISSION GEARBOX
ALIGNMENT TOOL INSTALLATION (END CAP ON RIGHT ANGLE GEARBOX)
Flap Right Angle Gearbox Alignment Figure 402
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-67
 ALL  ú ú 01 Page 404 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 2)  Make sure the end cap (the end opposite the spring) is on the transmission.
 (b)  
Make sure the cable is in the tolerance zone in the vertical and the horizontal plane.

 (c)  
Remove the alignment tool between the right angle gearbox and the transmission gearbox.

 (d)  
Install the alignment tool with the end cap on the right angle gearbox.

 (e)  
Make sure the cable is in the tolerance zone in the vertical and the horizontal plane.

 (f)  
If the cable is not in the tolerance zone, align the right angle gearbox:

 NOTE: Do not move the transmission gearbox to align the right
____
 angle gearbox.

 1) Install a maximum of 0.064-inch shims below the housing bolts if it is necessary to align the gearbox. 2) An example of a vertical adjustment: a) Install a 0.032-inch washer below the gearbox mounting pad at the bolt No. 1 or 3. b) Install a 0.016-inch washer at the bolt No. 2. 3) An example of a horizontal adjustment: a) Install a 0.016-inch washer below the mounting pad at the bolt No. 1 and 3, or bolt No. 2.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(101)