H46972
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-05
 ALL  ú ú 01 Page 403 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 024-083
 (7)  
AIRPLANES WITH THREE PUSHRODS; Disconnect the exhaust gate assembly from the midflap:

 (a)  
Remove the exhaust gate mounting bolts, washers, nuts and cotter pins.

 S 024-084
 (8)  
AIRPLANES WITH TWO PUSHRODS; Disconnect the exhaust gate assembly from the midflap:

 (a)  
Remove the exhaust gate mounting bolts, washers, and nuts.

 S 024-094
 (9)  Remove the exhaust gate assembly from the midflap.
 TASK 27-51-05-404-016
 3. Inboard Trailing Edge Flap Exhaust Gate Installation (Fig. 401)
____________________________________________________
 A. Special Tools and Equipment
 (1) Rig Pins (F-5 and F-6) - 0.248 +0.000/-0.002 inch diameter,
 3.7 |0.25 inches long (MS20392-3)
 NOTE: The rig pins are part of kit F70207-69, -78, or -83.
____
 B. References
 (1)  
AMM 27-51-00/201, Trailing Edge Flap System

 (2)  
AMM 27-51-04/501, Inboard Trailing Edge Flap

 (3)  
AMM 27-51-04/601, Inboard Trailing Edge Flap

 C.
Access

 (1)  
Location Zone 101, 102 Control Cabin 309, 409 Wing Trailing Edge Inboard Flap and Spoiler

 D.
Install the Inboard Trailing Edge Flap Exhaust Gate

 S 224-017
 (1)  
If you will install used parts, do this task: Inboard Flap Inspection (AMM 27-51-04/601).

 (2)  
Install the inboard flap exhaust gate:

 S 424-091

 (3)  
AIRPLANES WITH THREE PUSHRODS; Attach the exhaust gate to the midflap with the bolts, washers, nuts and cotter pins.

 (a)  
Tighten the nuts to 30-40 pound-inches.

 S 424-020
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-05
 ALL  ú ú 01 Page 404 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  Tighten the nuts to the nearest cotter pin hole and install the cotter pins.
 S 424-092
 (4)  
AIRPLANES WITH TWO PUSHRODS; Attach the exhaust gate to the midflap with the bolts, washers and nuts.

 (a)  
Tighten the nuts to 100-120 pound-inches.

 E.
Adjust the Inboard Flap Exhaust Gate

 S 864-095
 (1)
Do this task: Pressurize Hydraulic System B (AMM 27-51-00/201).

 S 864-096

 (2)
Put the flap control lever in the UP detent to retract the flaps.

 S 864-097

 (3)
Do this task: Depressurize Hydraulic System B (AMM 27-51-00/201).

 S 824-043

 (4)  
AIRPLANES WITH THREE PUSHRODS;
 Adjust the exhaust gate rods (Fig. 402):

 (a)  
Remove the outboard panel from the lower surface of the midflap.

 (b)  
Install the rig pin in the FLAP-UP rig pin hole in the exhaust gate mechanism. 1) If you cannot install the rig pin, adjust the rod attached

 to the foreflap:
 a) Remove the rod that is attached to the foreflap and the

 exhaust gate mechanism. b) Install the rig pin into the FLAP-UP rig pin hole. c) Adjust the length of the rod. d) Install the rod on the foreflap and the exhaust gate
 mechanism.
 e) Remove the rig pin.

 (c)  Make sure the trailing edge of the exhaust gate and the aftflap align in the limits of +0.00 to -0.15 inch.
 NOTE: Make sure the trailing edge of the exhaust gate is below
____
 the aftflap.

 (d)  If the exhaust gate and the trailing edge are not in the tolerance, adjust the exhaust gate: 1) Hold the trailing edge of the exhaust gate. 2) Install the rig pin into the FLAP-UP rig pin hole.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 飛行操縱 FLIGHT CONTROLS 4(6)