(b)  
Move the flap control lever from the UP detent to the 5-unit position. 1) Make sure the speed of the TE flap drive torque tube

 decreases during the leading edge flap extension.
 2)  Make sure that system B pressure does not show less than 2325 psi for more than 1 second during the TE flaps extension.
 3)  Make sure the speed of the TE flap drive torque tube increases when the leading edge flaps and slats are fully extended.
 4)  Make sure the system B pressure stays between 2325 and 2800 psi while the TE flaps extend to the 5-unit position.
 (c)  Put the flap control lever in the UP detent. 1) Make sure the speed of the TE torque tube decreases during the leading edge flap and slat retraction.
 2)  Make sure the system B pressure does not show less than 2325 psi for more than 1 second during the TE flaps retraction.
 3)  Make sure the speed of the TE torque tubes increases when the leading edge flaps and slats are retracted. 4) Make sure the system B pressure stays between 2325 and 2800 psi while the TE flaps retract to the 0-degree position.
 S 864-016
 (9)  Do this task: "Hydraulic System B Depressurization" (AMM 29-15-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-84
 ALL  ú ú 02 Page 405 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 FLAP DEFLECTION CONTROL PLUNGER - REMOVAL/INSTALLATION
______________________________________________________
 TASK 27-51-86-004-015
 1.  Flap Deflection Control Plunger Removal_______________________________________
 A. References
 (1)  
AMM 12-31-01/201, Zone Diagrams

 (2)  
AMM 12-31-61/201, Wing Lower Surface Access Doors and Panels

 (3)  
AMM 27-51-00/201, Trailing Edge Flap Systems

 (4)  
AMM 29-15-00/201, Pressurize Hydraulic System A, B, or Standby

 B.
Access

 (1)  
Location Zone 307 Left Wing Trailing Edge Outboard Flap and Spoilers 407 Right Wing Trailing Edge Outboard Flap and Spoilers

 (2)  
Access Panels
 8215L Exhaust-Gate Linkage Access Panel
 8715R Exhaust-Gate Linkage Access Panel

 C.
Prepare for the Removal

 S 864-019
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
_______ SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS, ELEVATORS, FLAPS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1) Do this task to pressurize hydraulic system B: "Pressurize Hydraulic System A, B, or Standby" (AMM 29-15-00/201).
 S 864-020
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE TRAILING
_______ EDGE FLAPS, THE LEADING EDGE FLAPS AND SLATS AND THE DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (2)  
Put the flap control lever in the 40-unit detent to extend the flaps.

 S 864-022

 (3)  
Do this task: "Trailing Edge Flap System Deactivation" (AMM 27-51-00/201).

 (4)  
Remove the inboard flap, outboard track fairing tailcone.

 S 024-006
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-86
 ALL  ú ú 01 Page 401 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
SEE A
MIDFLAP 
AFTFLAP 
FWD 
SEE  B  MECHANISM EXHAUST GATE  FOREFLAP  INBD 
(RIGHT FLAP OPPOSITE) LEFT FLAP A 

Flap Deflection Control Plunger Installation
Figure 401 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-86
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(150)