曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 S 824-019
 (8)  Adjust the side rollers:
 (a) Tighten the two roller bolts to 30-40 pound-inches.
 (b) Find the midpoint between the two carriage halves (5) and (8)
 at the side rollers.
 (c) Make sure the distance between the side rollers is 1.40 to 1.41
 inches.
 (d) Make sure the distance between each roller and the midpoint
 between the carriage halves is 0.70 to 0.71 inch.
 1) Add or remove the shim laminations below the side rollers
 to get the correct clearance.
 (e) Tighten the mounting bolts for the side roller to 30-40
 pound-inches.
 (f) Install the lockwire on the bolts.
 S 434-020
 (9)  Do this task: "Inboard Trailing Edge Flap Installation"
 (Ref 27-51-04/401).
 S 434-021

 (10)
 On the inboard carriage, install the pulley bracket (11) on the carriage halves:

 (a)
Put the pulley bracket on the carriage half.

 (b)
Apply the primer on the bolts.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-14
 ALL  ú ú 01 Page 407 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (c)  
Install the bolts with the wet primer.

 (d)  
Adjust the pulley bracket (11) until the cables align with the opening in the midflap.

 (e)  
Tighten the bolts.

 S 434-022
 (11)
 Tighten the boom cables:

 (a)  
Tighten the cables until they are not loose and remove the cable clamps.

 S 824-023
 (12) Do this task to adjust the boom cables:  "Aftflap Actuating Mechanism Boom Installation" (27-51-19/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-14
 ALL  ú ú 01 Page 408 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 INBOARD MIDFLAP CARRIAGE - INSPECTION/CHECK
___________________________________________
 1.  General_______
 A.  There is one task in this procedure: an inspection of the inboard midflap carriage. To do the inspection, you measure the diameters of the bushings and bolts that attach the inboard midflap carriage.
 TASK 27-51-14-226-001
 2.  Inboard Midflap Carriage Inspection___________________________________
 A.  Standard Tools and Equipment
 (1)  
Micrometer - 0 to 1 inch

 (2)  
Vernier Caliper

 B.  
References

 (1)  
27-51-14/401, Inboard Midflap Carriage

 C.  
Access

 (1)  
Location Zone 309, 409 Wing Inboard Trailing Edge Flap and Spoilers

 D.  
Procedure

 S 026-002
 (1)  
Do this task: "Inboard Midflap Carriage Removal"
 (Ref/27-51-14/401).

 S 226-003

 (2)  
Measure the parts of the roller on the inboard carriage (Fig. 601):

 (a)  
Remove the parts.

 (b)  
Use a micrometer or a vernier caliper to measure the parts.

 (c)  
Compare the dimensions you measured with the permitted dimensions shown in Fig. 601.

 (d)  
Replace the parts that are not in the tolerance.

 (e)  
Install the parts.

 S 426-004
 (3)  Do this task: "Inboard Midflap Carriage Installation" (Ref 27-51-14/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-14
 ALL  ú ú 01 Page 601 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
CARRIAGE HALF  A 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(17)