(d)  
Install the inboard bolt with a new torque indicating washer.

 (e)  
Install the outboard bolt with a countersunk washer.

 (f)  
Install the nuts and washers.

 (g)  
Tighten the inboard bolt until the outer ring of the torque indicating washer does not turn: 1) If the bolt touches the bottom on the barrel nut, install a

 washer under the head of the bolt.

 (h)  
Tighten the outboard nut to 360-420 pound-inches. 1) Make sure a minimum of one thread extends through the nut.

 (i)  
Install the lockwire on the heads of the bolts.

 S 164-011
 (3)  
Clean the area around the bolt heads.

 S 394-012

 (4)  
Apply a bead of the sealant around the bolt heads.

 G.  
Put the Airplane Back to Its Usual Condition

 S 644-017
 (1)  
Do the step to lubricate the outboard Trailing edge flaps if it is necessary (AMM 12-22-51/301).

 S 434-013

 (2)  
Do this task : "Outboard Foreflap Sequence Carriage Installation" (AMM 27-51-47/401).

 (3)  
Do this task: "Transmission Installation" (AMM 27-51-71/401)

 (4)
Do this task: "Outboard Flap Installation" (AMM 27-51-34/401).

 S 434-014
 S 434-015
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-49
 ALL  ú ú 01 Page 408 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 OUTBOARD FLAP TRACKS - INSPECTION/CHECK
_______________________________________
 1.  General_______
 A.  There is one task in this procedure; An inspection of the outboard flap tracks. To do the inspection, you measure the inner and outer diameters of the parts that attach the flap tracks.
 TASK 27-51-49-226-001
 2.  Outboard Flap Track Inspection______________________________
 A.  Standard Tools and Equipment
 (1)  
Micrometer - 0 to 1 inch

 (2)  
Vernier Caliper

 B.  
References

 (1)  
27-51-49/401, Outboard Flap Tracks

 C.  
Access

 (1)  
Location Zone 307, 407 Wing Trailing Edge Outboard Flap and Spoilers

 D.  
Procedure

 S 036-002
 (1)
Do this task: "Outboard Flap Track Removal" (Ref 27-51-49/401).

 S 226-003

 (2)  
Measure the parts that attach the flap track (Fig. 601):

 (a)  
Remove the parts.

 (b)  
Use a micrometer or a vernier caliper to measure the parts.

 (c)  
Compare the dimensions you measured with the permitted dimensions shown in Fig. 601.

 (d)  
Repair or replace all parts that are not in the tolerance, as shown in Fig. 601.

 (e)  
Install the parts.

 S 436-004
 (3)  Do this task: "Outboard Flap Track Installation"
 (Ref 27-51-49/401).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-49
 ALL  ú ú 01 Page 601 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
SEE A
B
SEEB  B
FWD
A
AFT TRACK SUPPORT FITTING
A
SEE C
TAPERED SHIM
A
FWD  FLAP TRACK
5
INBD
B
FWD INBD
C
Outboard Flap Track Wear Limits
Figure 601 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-49
 ALL  ú ú 01 Page 602 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(81)