曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (c)  Keep the 0.42-inch dimension and adjust the adjustment nuts to get a cable tension of 100 |10 pounds.
 NOTE: The temperature must be approximately 70°F when you
____ adjust the tension. If the temperature decreases, you must decrease the tension. If the temperature increases, you must increase the tension. Do not change the tolerance to more than the 10-pound limit.
 1) Put the tensiometer on the cable between the rig pins and the aft cable adjustment nut. 2) Move the cable away from the boom to install the tensiometer. 3) Release the cable when you adjust the tension.
 S 414-017
 (9)  
Install the cable guard (4).

 S 834-018

 (10)
 Remove the rig pins F-5 and F-6 from the boom.

 S 864-019

 (11)
 Supply the system B hydraulic power (AMM 27-51-00/201).

 S 714-020

 (12)
 Extend and retract the flaps.

 (a)  
Make sure the aftflap drive mechanism moves correctly.

 (13)
 Remove the system B hydraulic power (AMM 27-51-00/201).

 S 414-022

 (14)
 Install these access panels on the lower surface of the midflap:

 (a)  
For the left side: 8403 and 8404

 (b)  
For the right side: 8503 and 8504

 (15)
 Install the inboard flap track fairing (AMM 27-51-32/401).

 S 864-021
 S 414-023
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-24
 ALL  ú ú 03 Page 407 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 INBOARD FLAP TRACKS - REMOVAL/INSTALLATION
__________________________________________
 1.  General
_______
 A.  There are four tasks in this procedure. There are tasks for the removal and tasks for the installation of the inboard flap tracks.
 B.  There are solid tapered aluminum shims and aluminum anti-fret strips installed on the inboard flap outboard track at the aft support fitting. It is very important to keep the initial thickness of the shims. The installation procedure has instructions for the replacement of damaged or lost shims. If you do not follow the instructions, the flap track can be not aligned.
 TASK 27-51-27-004-001
 2.  Inboard Flap Outboard Track Removal
___________________________________
 A.  References
 (1)
AMM 27-51-04/401, Inboard Trailing Edge Flap

 (2)
AMM 27-51-71/401, Flap Transmission

 (3)
AMM 54-51-01/201, Inboard Flap Outboard Track Fairing

 B.  
Access

 (1)  
Location Zone 309 Left Wing Trailing Edge Inboard Flap and Spoilers 409 Right Wing Trailing Edge Inboard Flap and Spoilers

 (2)  
Access Panel
 8117L Access Panel
 8817R Access Panel

 C.  
Procedure

 S 014-002
 (1)
Do this task: "Flap Track Fairing Removal" (AMM 54-51-01/201).

 S 034-003

 (2)
Do this task: "Inboard Flap Removal" (AMM 27-51-04/401).

 (3)
Do this task: "Transmission Removal" (AMM 27-51-71/401).

 S 024-005

 (4)
Remove the flap track (Fig. 401):

 (a)
Remove the bolts from the aft support fitting.

 S 034-004
 1)  Make sure you do not cause damage to the anti-fret strip or the tapered shim when you remove the track.
 NOTE: The anti-fret strip is bonded to the lower wing
____ surface. The tapered shim is bonded to the top surface of the flap track.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-27
 ALL  ú ú 01 Page 401 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE  B 
SEE  C 
SEE  A  FORWARD 
SUPPORT 
FITTING 
FWD 
INBD 
A 
ANTI-FRET STRIP 
FLANGED SPACER 
THICK WASHER 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(25)