EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-27
ALL ú ú 01 Page 402 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b)
Remove the bolts that attach the track to the forward support fitting.
(c)
Remove the flap track from the airplane.
S 034-006
(5)
Remove the forward support fitting if it is necessary:
(a)
Remove the applicable access panel 7216 or 7416.
(b)
Remove the bolts that attach the forward support fitting to the wing.
(c)
Remove the forward support fitting from the airplane.
TASK 27-51-27-404-007
3. Inboard Flap Outboard Track Installation________________________________________
A. Special Tools and Equipment
(1) Inboard Flap Rigging Beam - F80209-3
NOTE: The Rigging Beam is a part of F80209-1.
____
B. Consumable Materials
(1)
A00490 Sealant -BMS 5-95, Class B
(2)
C00308 Corrosion Preventive Compound - MIL-C-11796, Class 3
(3)
C00325 Primer - BMS 10-11, Type I
FRONT SPAR
REAR SPAR CL CL
INBOARD FLAP
RIGGING BEAM
Inboard Flap Outboard Track Installation
Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-27
ALL ú ú 02 Page 403 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(4)
D00633 Grease - BMS 3-33 (Recommended)
(5)
D00013 Grease - MIL-G-23827 (Alternate)
C.
References
(1)
AMM 12-22-51/301, Trailing Edge Flap System Lubrication - Servicing
(2)
AMM 27-51-04/401, Inboard Trailing Edge Flap
(3)
AMM 27-51-27/601, Inboard Flap Tracks
(4)
AMM 27-51-71/401, Flap Transmission
(5)
AMM 54-51-01/201, Inboard Flap Outboard Track Fairing
D.
Access
(1)
Location Zone 309 Left Wing Trailing Edge Inboard Flap and Spoilers 409 Right Wing Trailing Edge Inboard Flap and Spoilers
(2)
Access Panel
8117L Access Panel
8817R Access Panel
E.
Procedure
S 224-008
(1)
If you will install used parts, do this task: "Inboard Flap Track Inspection" (AMM 27-51-27/601).
S 434-009
(2)
Install the forward support fitting if it is necessary (fig. 401):
(a)
Install the inboard bolts: 1) Apply a layer of grease to the flanged spacers and the
thick washers.
2) Apply a layer of the sealant on the bolts.
3) Put the countersunk washer and the thick washer on the
bolt.
4) Install the bolt with the head down.
5) Install the flanged bushing in the support fitting with the
flange up. 6) Put the anti-fret strip between the support fitting and the wing.
(b) Put the support fitting on the lower surface of the wing and temporarily install the inboard bolts, washers and nuts.
CAUTION: MAKE SURE THE BOLTS ON THE FORWARD SUPPORT FITTING HAVE
_______ THE CORRECT GRIP LENGTH. INCORRECT BOLTS CAN CAUSE A FUEL LEAK.
(c) Install the outboard bolts: 1) Apply a layer of the sealant to the bolts. 2) Put the anti-fret strip between the support fitting and the
wing. 3) Put the countersunk washer on the bolt and install the bolt with the head down. 4) Install the washer and the nut on the bolt.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(26)
