27-51-52
 ALL  ú ú 01 Page 402 ú Nov 15/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
SEE A
LANDING LIGHT
CENTER
PUSH/PULL
FORWARD FAIRING
FAIRING ROD END
SEE C
CABLE ASSEMBLY  SEE B
FWD  CAM ARM  FORWARD BRACKET  CABLE CLAMP  AFT BRACKET 
A 
ROD END  ELECTRICAL CONNECTOR  SUPPORT (FIXED) TRACK FAIRING OUTBOARD FLAP  HINGE FITTING CENTER FAIRING 

CAM 
ARM 
ROD END 
INBD
SPACER 
LANDING LIGHT  FWD  CAM FOLLOWER 
ACTUATING ARM  RIG PIN  LANDING LIGHT  LANDING LIGHT 
CAM TRACK 
FWD  B  C
Landing Light Adjustment
Figure 402 

F91482
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-52
 ALL  ú ú 03 Page 403 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 864-004
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE TRAILING
_______ EDGE FLAPS, THE LEADING EDGE FLAPS AND SLATS AND THE DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (2)  
Move the flap control lever to the flaps position 40 (flaps down) detent to extend the flaps.

 S 864-006

 (3)  
Do this task to depressurize hydraulic system B: "Depressurization of Hydraulic System A, B, or Standby" (Ref 29-15-00/201).

 S 044-007

 (4)  
Do this task: "Trailing Edge Flap System Deactivation"
 (Ref 27-51-00/201).

 D.
Remove the Center Fairing

 S 014-008
 (1)  
Remove the access panel from the center fairing to get access to the center fairing hinge fitting (Fig. 401).

 S 034-009

 (2)
At the outboard track center fairing, disconnect the landing light:

 NOTE: It is necessary to disconnect the landing light for the
____ removal of the center fairing at the outboard track.
 (a)  
Remove the aft fairing from the center fairing.

 (b)  
Disconnect the electrical connector from the landing light (Fig. 402).

 (c)  
Remove the landing light cam track to disengage the cam follower.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-52
 ALL  ú ú 02 Page 404 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (d)  Disconnect the rod end on the push/pull cable to the cam arm and the cam follower.
 S 024-030
 (3)  
Remove the center fairing (Fig. 401):

 (a)  
Remove the fasteners and bushings that attach the center fairing hinge fitting to the flap track fairing support (Fig. 401).

 NOTE: Remove the bushings from the side of the clevis with the
____
 larger hole.

 (b)  
Move the center fairing aft to release the fairing tracks from the track rollers.

 (c)  
If you will install a different center fairing, remove the cam track from the fairing.

 NOTE:____Keep all shims from the center fairing. You will use these shims to install the cam track on the new center fairing. You must install the shims in the same positions.
 TASK 27-51-52-404-013
 3.  Outboard Flap Track Center Fairing Installation_______________________________________________
 A. References
 (1)  
27-51-00/201, Trailing Edge Flap System
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(83)