C.
Procedure

 S 224-025
 (1)  
If used parts are installed do this task: "Outboard Foreflap Sequence Carriage Inspection" (Ref 27-51-47/601).

 S 424-026

 (2)  
Install the foreflap carriage toggle on the sequence carriage (Fig. 401):

 (a)  
Put the toggle on the sequence carriage.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-47
 ALL  ú ú 01 Page 405 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b) (c) (d) (e)  Install the center bolt, washer and nut on the toggle.Install the bolts and washers on the two sides of the toggle.Install the bearings and the nuts on the bolts.Tighten the nuts and install the cotter pins.
 (3)  S 434-027Do this task:  "Trailing Edge Flap Installation" (Ref 27-51-34/401).
 (4)  S 444-028Do this task:  "Trailing Edge Flap System Activation"

 (Ref 27-51-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-47
 ALL  ú ú 01 Page 406 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 OUTBOARD FOREFLAP SEQUENCE CARRIAGE - INSPECTION/CHECK
______________________________________________________
 1.  General_______
 A.  There are two tasks in this procedure. There is an inspection of the outboard foreflap sequence carriage, and an inspection of the outboard foreflap toggle bearings.
 TASK 27-51-47-206-001
 2.  Outboard Foreflap Sequence Carriage Inspection______________________________________________
 A.  General
 (1)  
To do this check you measure the diameter or the thickness of the parts which attach the sequence carriage.

 (2)  
You usually do this task before you install a sequence carriage.

 B.  
Standard Tools and Equipment

 (1)  
Micrometer - 0 to 1 inch

 C.  
References

 (1)  
27-51-47/401, Outboard Foreflap Sequence Carriage

 D.  
Access

 (1)  
Location Zone 307, 407 Wing Trailing Edge Outboard Flap and Spoilers

 E.  
Procedure

 S 026-002
 (1)  
Do this task: "Outboard Foreflap Sequence Carriage Removal" (Ref 27-51-47/401).

 S 226-003

 (2)  
Examine the parts which attach the foreflap sequence carriage for worn areas:

 (a)  
Remove the parts to be examined.

 (b)  
Measure the parts.

 NOTE: Use a micrometer to measure the parts.
____
 (c)  
Compare the dimensions you measured with the permitted dimensions shown in Fig. 601.

 (d)  
Replace the parts which are not in the tolerance.

 (e)  
Install the parts.

 S 426-004
 (3)  Do this task: "Outboard Foreflap Sequence Carriage Installation" (Ref 27-51-47/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-47
 ALL  ú ú 02 Page 601 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEQUENCE CARRIAGE  TRACK FLAP  SEE A 
B 
A  A 
TOGGLE 
FWD  (2 LOCATIONS) STRIP 5. RUB  B 
INBD  (2 LOCATIONS)6. SLIDER A  FWD  INBD 

4. BUSHING/ 3. BUSHING/ BUSHING BOLT
1. BEARING/ BUSHING  2. BUSHING/ BOLT  BOLT 2. BUSHING/
A-A  B-B 

Outboard Foreflap Sequence Carriage Installation
Figure 601 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(75)