27-51-79
 ALL  ú ú 01 Page 501 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
SEE B
TRAILING EDGE FLAP CONTROL VALVE
LEADING EDGE FLAP CONTROL VALVE SEE C
FWD
NOTE:THE FLAP CONTROL UNIT IS SHOWN WITH THE LOWER PAN REMOVED.
A
Trailing Edge Flap Control Valve Adjustment
Figure 501 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-79
 ALL  ú ú 01 Page 502 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500
MAINTENANCE MANUAL

INDEX SURFACE |0.010 INCH 
RIG PIN F-1 
SLIDE VALVE 
B 
CAM  FOLLOWER CAM 

EDGE LINK LEADING  FWD 
INBD 
CHECKNUT  0.19 INCH MAX.  CAM LINK TRAILING EDGE  C  SEE  D 
0.94 INCH MAX. 

CAM LINK TRAILING EDGE  SLEEVE  D  CHECKNUT 
Figure 501 (Sheet 2) Trailing Edge Flap Control Valve Adjustment 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-79
 ALL  ú ú 01 Page 503 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 825-007

 (2)  
If the valve slide and the index surface do not align in the limit, adjust the trailing edge cam link:

 (a)  
Remove the lockwire from the cam link.

 (b)  
Loosen the two checknuts on the cam link.

 (c)  
Adjust the sleeve until the valve slide and the index surface align in the limit of |0.010 inch.

 (d)  
Tighten the checknuts and install the lockwire on the cam link.

 (e)  
Make sure that the threads of the rod end and the sleeve engage in the limits.

 (f)  
Adjust the rod end if the threads are not engaged in the limits: 1) Remove the bolt from the rod end. 2) Loosen the checknut. 3) Turn the rod end and the sleeve to get the correct

 dimension.
 4) Install the bolt, washer and nut to attach the rod end.
 5) Make sure the valve slide and the index surface align in
 the limits.
 S 215-008
 CAUTION:_______MAKE SURE THE RIG PIN F-1 IS NOT INSTALLED. YOU CAN CAUSE DAMAGE TO THE FLAP CONTROL UNIT WHEN YOU APPLY HYDRAULIC POWER IF THE RIG PIN IS INSTALLED.
 (3)  
Remove the rig pin F-1.

 S 865-009

 (4)  
Do this task: "Hydraulic System B Pressurization" (Ref 27-51-00/201).

 S 865-010

 (5)  
Put the flap control lever in the 5-unit detent to extend the flaps.

 S 865-011

 (6)  
Put the flap control lever in the UP detent to retract the flaps.

 S 865-012

 (7)  
Stop for 2 minutes, then do this task: "Hydraulic System B Depressurization" (AMM 27-51-00/201).

 S 835-013

 (8)  
Make sure you can install the rig pin F-1 freely in the flap control unit.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-79
 ALL  ú ú 01 Page 504 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 825-014
 (9)  
If you cannot install the rig pin freely, adjust the trailing edge cam link:

 (a)  
Remove the lockwire and loosen the two checknuts.

 (b)  
Remove the rig pin F-1.

 (c)  
Do this task: "Hydraulic System B Pressurization"
 (Ref 27-51-00/201).

 CAUTION: DO NOT INSTALL THE RIG PIN F-1 WITH THE HYDRAULIC SYSTEM
_______ PRESSURIZED. YOU CAN CAUSE DAMAGE TO THE FLAP CONTROL UNIT IF YOU INSTALL THE RIG PIN WITH THE HYDRAULIC SYSTEM PRESSURIZED.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(141)