TASK 27-51-34-226-012-002
 3. Outboard Trailing Edge Flap Exhaust Gate Actuation Mechanism Inspection
_______________________________________________________________________
 A. Standard Tools and Equipment
 (1)  
Micrometer 0 to 1 inch

 B.
References

 (1)  
AMM 27-51-34/401, Outboard Trailing Edge Flap

 C.
Access

 (1)  
Access Panels
 8215, 8715 Exhaust Gate Linkage Access Panel

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH TWO EXHAUST GATE ú

 27-51-34
 PUSHRODS.  ú CONFIG 2 ú 02 Page 612 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 D. Procedure
 S 016-013-002
 (1)  
Do this task: "Outboard Trailing Edge Flap Removal"
 (AMM 27-51-34/401).

 S 226-014-002

 (2)  
Measure the parts on the actuator mechanism for the exhaust gate (Fig. 602):

 (a)  
Remove the parts.

 (b)  
Use a micrometer to measure the parts.

 (c)  
Compare the dimensions you measured with the permitted dimensions shown in Fig. 602.

 (d)  
Replace the parts that are not in the tolerance.

 (e)  
Install the parts.

 S 416-015-002
 (3)  Do this task: "Outboard Trailing Edge Flap Installation" (AMM 27-51-34/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH TWO EXHAUST GATE ú

 27-51-34
 PUSHRODS.  ú CONFIG 2 ú 01 Page 613 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 EXHAUST GATE ACTUATOR PUSHRODS - REPAIRS
___________________________________________
 1.  General_______
 A.  There is one task in this procedure, a repair of the pushrods for the outboard exhaust gate actuator mechanism. The repair includes the replacement of the rivets that attach the pushrod to the rod end fitting.
 TASK 27-51-34-308-001
 2.  Exhaust Gate Actuator Pushrod Repair (Fig. 801)____________________________________
 A.  Standard Tools and Equipment
 (1)  
Shear Rivets - BACR15BB4D9

 (2)  
Shear Rivets - BACR15BB5D10

 B.  
References

 (1)  
AMM 27-51-34/401, Inboard TE Flap

 C.  
Access

 (1)  
Location Zone 307, 407 Wing Trailing Edge Outboard Flap and Spoilers

 D.  
Procedure

 S 028-002
 (1)  
Remove the pushrod for the exhaust gate actuator mechanism (AMM 27-51-34/401).

 S 358-003

 (2)  
Repair the pushrod:

 WARNING:_______DO NOT MAKE THE RIVET HOLES LARGER. YOU WILL CAUSE DAMAGE TO THE PUSHROD AND THE ROD END FITTING.
 (a)  
Remove the broken parts of the rivets from the holes in the pushrod.

 (b)  
Install the new rivets.

 S 428-004
 (3)  Install the pushrod for the exhaust gate actuator mechanism (AMM 27-51-34/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-34
 ALL  ú ú 01 Page 801 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500
MAINTENANCE MANUAL

SEE A
SEE A
MIDFLAP 
AFTFLAP 
FWD
EXHAUST GATE MECHANISM  SEE B EXHAUST GATE  LEFT FLAP (RIGHT FLAP IS OPPOSITE) A FOREFLAP  INBD 
Outboard Flap Exhaust Gate Pushrods Repairs Figure 801 (Sheet 1) 

K29802
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(55)