27-51-27
 ALL  ú ú 01 Page 607 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 INBOARD MIDFLAP SEAL PLATE - REMOVAL/INSTALLATION
_________________________________________________
 1.  General_______
 A.  There are two tasks in this procedure. There is a task for the removal and a task for the installation of a seal plate for the inboard midflap. This procedure is applicable to the left and the right seal plate.
 TASK 27-51-29-004-001
 2.  Inboard Midflap Seal Plate Removal (Fig. 401)__________________________________
 A.  References
 (1)  
27-51-00/201, Trailing Edge Flap System

 B.  
Access

 (1)  
Location Zone 309, 409 Wing Trailing Edge Inboard Flap and Spoilers

 C.  
Procedure

 S 864-002
 (1)  
Supply the system B hydraulic power (AMM 27-51-00/201).

 S 864-003

 (2)  
Put the flap control lever in the 40-unit detent to extend the flaps.

 S 864-004

 (3)  
Remove the system B hydraulic power (AMM 27-51-00/201).

 S 024-005

 (4)  
Remove the seal plate from the midflap:

 (a)  
Remove the bolts and screws from the seal plate.

 (b)  
Remove the seal plate from the midflap.

 (c)  
Keep all filler plates and shims for the seal plate.

 TASK 27-51-29-404-006
 3.  Inboard Midflap Seal Plate Installation (Fig. 401)_______________________________________
 A.  Consumable Materials
 (1)  
A00247 Sealant BMS 5-95, Class C

 (2)  
C00259 Primer BMS 10-11, Type I

 B.  
References

 (1)  
27-51-00/201, Trailing Edge Flap System

 C.  
Access

 (1)  
Location Zone 309, 409 Wing Trailing Edge Inboard Flap and Spoilers

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-29
 ALL  ú ú 01 Page 401 ú Nov 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

BOLT (4 LOCATIONS)
(4 LOCATIONS)
AFT
SEAL
PLATE

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-29
 ALL  ú ú 01 Page 402 ú Mar 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 D. Procedure
 S 424-007
 (1)  
Install the seal plate on the midflap:

 (a)  
Apply the primer to the shims and fillers.

 (b)  
Put the seal plate in its position on the midflap.

 (c)  
Apply the sealant to the shims and fillers and put them on the seal plate.

 (d)  
Install the bolts and screws.

 (e)  
Put the seal plate at the approximate center of the holes that have slots.

 (f)  
Tighten the bolts and screws.

 S 864-008
 (2)  
Supply the system B hydraulic power (AMM 27-51-00/201).

 S 864-017

 (3)  
Put the flap control lever in the 5-unit detent to extend the flaps.

 (a)  
Adjust the aft seal plate to get a clearance of 0.030-0.050 inch between the seal plate and the wing-to-body fairing at the nearest three points. 1) Add or remove spacers to move the seal plate outboard or

 inboard.
 NOTE:____Measure to find the bolt grip length required. Make sure that the bolts selected provide a positive clamp-up.
 (b)  Tighten the bolts to 100-140 pound-inches.
 S 864-009
 (4)
Put the flap control lever in the UP detent to retract the flaps.

 S 824-015

 (5)  
Make sure the hook engages the flap track fairing.

 (a)  
Adjust the aft seal plate to get a clearance of 0.030-0.050 inch between the wing-to-body fairing and the lower part of the seal plate at the nearest point.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(32)