曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

SPL-1732 Equipment - Removal/Installation, Rudder PCU
(Part #: C27049-36, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
(Opt Part #: C27049-1, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
STD-203 Container - Oil Resistant, 1 U.S.-Gal (3.8 l)
C. Consumable Materials
Reference Description Specification
D00153 Fluid - Hydraulic, Erosion Arresting, Fire Resistant BMS3-11, Type
IV
(interchange~
able&
intermixable
with Type V)
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 001-005, 155-157, 201-999 PRE SB 737-27-1253 27-21-91
Config 1
Page 409
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
D. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
324 Vertical Fin - Rear Spar To Trailing Edge
E. Access Panels
Number Name/Location
324CL Vertical Fin, Access
324DL Trailing Edge Access
F. Main Rudder PCU Installation
SUBTASK 27-21-91-080-006-001
(1) Remove the lock, SPL-1727.
SUBTASK 27-21-91-480-011-001
(2) Install the equipment, SPL-1732 to the main rudder pcu installation [1] (Figure 402).
SUBTASK 27-21-91-420-005-001
CAUTION: MAKE SURE THAT YOU FOLLOW THE INSTRUCTIONS TO INSTALL THE MAIN
RUDDER CAREFULLY AND DO THE PROCEDURE IN THE SPECIFIED SEQUENCE.
DAMAGE TO THE VERNIER CONTROL ROD [9] MAY OCCUR IF YOU DO NOT FOLLOW
THE INSTRUCTIONS CORRECTLY.
(3) Install the main rudder pcu installation [1] (Figure 401):
(a) Use a 200 pounds (90.7 kilograms) fishpole to put the main rudder pcu installation [1] in its
position with the forward manifold [11] in the forward direction.
(b) Connect the forward manifold [11] to the vertical fin structure:
1) Install the washer [34], bushing [23], bolt assembly [22], washer [24], and nut [25].
2) Use the equipment, SPL-1731 to tighten the nut [25] to 1000-1200 pound-inches (113.0-
135.6 newton-meters).
3) Install the washer [26] and nut [27].
CAUTION: DO NOT TIGHTEN THE NUT [25] AFTER YOU TIGHTEN THE NUT [27]. THIS
CAN CAUSE DAMAGE TO EQUIPMENT.
4) Tighten the nut [27] to 650-800 pound-inches (73.4-90.4 newton-meters).
(c) Connect the rod assembly [2] to the rudder:
1) Install the bolt assembly [28], washer [29], and nut [30].
2) Tighten the nut [30] to 900-1050 pound-inches (101.7-118.6 newton-meters).
3) Install the washer [31] and nut [32].
CAUTION: DO NOT TIGHTEN THE NUT [30] AFTER YOU TIGHTEN THE NUT [32]. THIS
CAN CAUSE DAMAGE TO EQUIPMENT.
4) Tighten the nut [32] to 450-550 pound-inches (50.8-62.1 newton-meters).
SUBTASK 27-21-91-080-007-001
(4) Remove the equipment, SPL-1732 from the main rudder pcu installation [1]:
(a) Remove the screws [53] and washers [54] from the beam assembly [55].
(b) Remove the screws [51] and washers [52] from the bracket assembly [56].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 001-005, 155-157, 201-999 PRE SB 737-27-1253 27-21-91
Config 1
Page 410
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(c) Remove the bracket assembly [56] and beam assembly [55].
SUBTASK 27-21-91-420-006-001
(5) Install the vernier control rod [8]:
(a) Put the vernier control rod [8] in its position with the vernier adjustment end in the forward
direction.
(b) Make sure that you can see 7 +/- 1 threads on the forward end of the rod and the sleeve.
(c) Connect the vernier control rod [8] to the external summing lever [3] and rudder actuator
input crank [10]:
1) Install the bolt assemblies [4] and washers [5].
2) Tighten the outer bolt of the bolt assemblies [4] to 70-85 pound-inches (7.9-9.6 newtonmeters).
3) Install the washers [6] and nuts [7].
CAUTION: DO NOT TIGHTEN THE OUTER BOLT OF THE BOLT ASSEMBLY [4]
AFTER YOU TIGHTEN THE NUT [7]. THIS CAN CAUSE DAMAGE TO
EQUIPMENT.
4) Tighten the nuts [7] to 25-30 pound-inches (2.8-3.4 newton-meters).
SUBTASK 27-21-91-020-025-001
CAUTION: MAKE SURE THAT YOU CORRECTLY INSTALL THE HYDRAULIC LINES TO THE MAIN
RUDDER PCU. MAKE SURE THAT CORRECT UNIONS ARE INSTALLED IN THE
HYDRAULIC PORTS. YOU CAN CAUSE DAMAGE TO THE MAIN RUDDER PCU.
(6) Connect the hydraulic lines to the main rudder pcu installation [1]:
(a) Remove the caps and plugs from the hydraulic lines and ports.
(b) If the main rudder pcu installation [1] does not have unions and packings installed, then do
these steps:
1) Apply fluid, D00153 to the unions, reducer and packings.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊2(112)