曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

remove it, do this task: Rudder Pedal Position Sensor Removal, TASK 31-31-42-000-801.
F. Rudder Forward Quadrant Removal
(Figure 402, Figure 403)
SUBTASK 27-21-51-010-004
WARNING: YOU MUST LOOSEN AND DISCONNECT THE RUDDER CABLES FROM THE RUDDER
FORWARD QUADRANTS BEFORE YOU DISCONNECT THE BUS ROD. RELIEVE
TENSION UNIFORMLY IN THE TWO RUDDER CABLES. IF YOU DO NOT LOOSEN THE
RUDDER CABLES EQUALLY, IT CAN CAUSE INJURY TO PERSONNEL OR DAMAGE
TO EQUIPMENT.
(1) Loosen the turnbuckles [91] for the rudder cable RB [21] and rudder cable RA [22] (Figure 403).
SUBTASK 27-21-51-020-002
(2) Disconnect the applicable rudder cable from the rudder forward quadrant [39] that you will
remove (Figure 402):
(a) Remove the bolt [30] and washer [31] from the cable retainer [32].
(b) Remove the cable RB [21] or cable RA [22] from the rudder forward quadrant [39].
SUBTASK 27-21-51-020-003
(3) Remove the pins [44], nuts [43], washers [42], and bolts [41] to disconnect the rudder pedal
tension rods [40] from the rudder forward quadrant [39]. Discard the pins [44].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-21-51
Page 402
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-21-51-020-004
(4) Remove the pin [49], nut [48], washer [47], spacers [46], and bolt [45] to disconnect the bus rod
[50] from the rudder forward quadrant [39]. Discard the pin [49].
SUBTASK 27-21-51-020-010
(5) Remove the nuts [90], washers [89], and bolts [88] to remove the cover assembly [87] from the
floor beam structure.
SUBTASK 27-21-51-020-005
(6) Remove the nuts [73], washers [72], and bolts [71] to remove the adjustment shaft support
bracket [74] from the structure.
SUBTASK 27-21-51-020-006
(7) Pull the adjustment shaft [75] and the adjustment shaft support bracket [74] forward to disengage
the adjustment shaft [75] from the rudder forward quadrant [39].
SUBTASK 27-21-51-020-007
(8) Remove the nuts [54], washers [53], and screws [52] to remove the cable guard [51].
SUBTASK 27-21-51-020-008
(9) If you remove the captain’s rudder forward quadrant [39], then do these steps:
(a) Remove the lockwire from the rudder pedal steering arm [24].
(b) Remove the screws [68] and washers [69] to disconnect the rudder pedal steering arm [24]
from the rudder forward quadrant [39].
(c) Move the rudder pedal steering arm [24] out of the way.
(d) Hold the rudder forward quadrant [39] and remove the jackshaft support channel [70]:
NOTE: The rudder forward quadrant is free to fall from the upper bearing housing after
you remove the screws.
1) Remove the nuts [60], washers [59], and screws [58].
2) Remove the nut [63], washer [62], and screw [61].
(e) Remove the rudder forward quadrant [39] from the airplane:
1) Move the rudder forward quadrant [39] in an aft and outboard direction to clear the floor
beam penetration, and remove it from the airplane.
(f) Do these steps to remove the lower bearing housing [67] from the jackshaft support
channel [74]:
1) Remove the nuts [57], washers [56], and bolts [55].
2) Remove the nut [66], washer [65], and bolt [64].
SUBTASK 27-21-51-020-009
(10) If you remove the first officer’s rudder forward quadrant [39], then do these steps:
(a) Remove the lockwire from the rudder pedal position sensor quadrant [23].
(b) Remove the screws [77] and washers [78] to disconnect the rudder pedal position sensor
quadrant [23] from the rudder forward quadrant [39].
(c) Hold the rudder forward quadrant [39] and remove the jackshaft support channel [76]:
NOTE: The rudder forward quadrant is free to fall from the upper bearing housing after
you remove the bolts and screws.
1) Remove the nuts [60], washers [59], and screws [58].
2) Remove the nuts [85], washers [84], and bolts [83.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-21-51
Page 403
Jun 10/2004
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
3) Remove the support [86].
4) Remove the nut [63], washer [62], and screw [61].
(d) Remove the rudder forward quadrant [39] from the airplane:
1) Move the rudder forward quadrant [39] in an aft and outboard direction to clear the floor
beam penetration, and remove it from the airplane.
(e) Do these steps to remove the lower bearing housing [67] from the jackshaft support
channel [39]:
1) Remove the nuts [57], washers [56], and bolts [55].
2) Remove the nut [66], washer [65], and bolt [64].
------------------------- END OF TASK ---------------------------
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊2(92)