曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(d) Tighten the locknut [7] to 36-40 pound-inches (4.1-4.5 newton-meters).
(e) Bend the tab on the washer [8] over the the flat of the locknut [7].
NOTE: Small deformation of the star washer [8] is permitted.
SUBTASK 27-11-94-420-007
(3) Install the lightplate [1] with fasteners [4].
SUBTASK 27-11-94-420-008
(4) Install the rudder trim knob [2]:
(a) Make sure the surfaces between the rudder trim knob [2] and the lightplate [1] are free of
contaminates.
(b) Put the rudder trim knob [2] fully down on the rudder trim switch shaft [5].
(c) Make sure the rudder trim knob [2] is 0.010-0.050 inch (0.25-1.27 millimeters) from the top of
the lightplate [1].
(d) Install the set screws [6] on the rudder trim knob [5].
(e) Tighten the set screws [6] on the rudder trim knob [5].
SUBTASK 27-11-94-420-004
(5) Do this task: Aileron and Rudder Trim Control Module Installation, TASK 27-11-94-400-801.
SUBTASK 27-11-94-730-001
(6) If you replace the rudder trim switch [9], do this task: Rudder Trim System Test,
TASK 27-21-00-700-819-001 or Rudder Trim System Test, TASK 27-21-00-700-819-002.
SUBTASK 27-11-94-730-002
(7) If you replace the aileron trim switches [11], do this task: Aileron Trim Response Test,
TASK 27-11-00-730-801.
------------------------- END OF TASK ---------------------------
TASK 27-11-94-000-803
6. Rudder Trim Indicator Removal
(Figure 401)
A. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
B. Prepare for the Removal
SUBTASK 27-11-94-860-003
(1) Make sure the rudder is in the neutral position.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-11-94
Page 406
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-11-94-860-004
(2) Open these circuit breakers and install safety tags:
F/O Electrical System Panel, P6-2
Row Col Number Name
D 16 C00788 FLIGHT CONTROL TRIM IND RUD
D 19 C00787 FLIGHT CONTROL TRIM CONT RUD
C. Rudder Trim Indicator Removal
SUBTASK 27-11-94-020-005
(1) Remove the rudder trim indicator [14]:
(a) Remove the fasteners [13] that connect the rudder trim indicator [14] to the baseplate [6].
(b) Disconnect the electrical connector from the rudder trim indicator [14].
(c) Remove the rudder trim indicator [14] from the baseplate [6].
------------------------- END OF TASK ---------------------------
TASK 27-11-94-400-803
7. Rudder Trim Indicator Installation
(Figure 401)
A. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
B. Rudder Trim Indicator Installation
SUBTASK 27-11-94-420-005
(1) Install the rudder trim indicator [14]:
(a) Connect the electrical connector to the rudder trim indicator [14].
(b) Put the rudder trim indicator [14] on the baseplate [6].
(c) Install the fasteners [13] to attach the rudder trim indicator [14] to the baseplate [6].
SUBTASK 27-11-94-860-005
(2) Remove the safety tags and close these circuit breakers:
F/O Electrical System Panel, P6-2
Row Col Number Name
D 16 C00788 FLIGHT CONTROL TRIM IND RUD
D 19 C00787 FLIGHT CONTROL TRIM CONT RUD
SUBTASK 27-11-94-280-001
(3) Do a check to make sure the rudder trim indicator [14] is in the null position.
(a) With the rudder in the neutral position, make sure the the rudder trim indicator [14] is at the
zero position.
SUBTASK 27-11-94-820-001
(4) If the rudder trim indicator [14] is not at the null position, adjust the rudder trim indicator [14]:
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-11-94
Page 407
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(a) Remove the fasteners [13] that attach the rudder trim indicator [14] to the baseplate [6].
NOTE: Do not disconnect the electrical connector.
(b) Turn the adjustment screw on the bottom of the rudder trim indicator [14] until the indicator
is at 0.0 ±0.1 unit.
(c) Install the rudder trim indicator [14] to the baseplate [6] with the fasteners [13].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-11-94
Page 408
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
RUDDER AND RUDDER TRIM CONTROL SYSTEM - MAINTENANCE PRACTICES
1. General
A. This procedure has these tasks:
(1) Rudder Hydraulic System A, B, or Standby Pressurization
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊2(16)