曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(b) Push the cable [1] through the bearing retainer [12].
(c) Tighten the cable retaining nut [13].
1) Tighten the cable retaining nut [13] finger tight plus one quarter turn.
(d) Install the lockwire, G01048 on the retaining nut [13].
NOTE: To get the best lockwire angle, make sure that the aft cable assembly can turn
easily and smoothly.
SUBTASK 27-21-41-420-004
(4) Do these steps to install the crank lever [10]:
(a) Install the spacer [11] on the cable [1].
(b) Install the crank lever [10], washer [9], and nut [8].
SUBTASK 27-21-41-410-001
(5) Close the main instrument panel module assembly [14].
SUBTASK 27-21-41-410-002
(6) Close the main instrument panel module shroud.
SUBTASK 27-21-41-860-001
(7) Turn the crank lever to move the rudder pedals fully forward and then aft.
(a) Make sure the cable operates smoothly and freely.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-21-41
Page 408
Jun 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-21-41-710-001
(8) Do this task: Rudder Pedal Adjustment and Limit Travel Test, TASK 27-21-00-700-813-001 or
Rudder Pedal Adjustment and Limit Travel Test, TASK 27-21-00-700-813-002.
SUBTASK 27-21-41-410-003
(9) Close this access panel:
Number Name/Location
112A Forward Access Door
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-21-41
Page 409
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
RUDDER FORWARD QUADRANT - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of a rudder forward quadrant
(2) An installation of the a rudder forward quadrant.
B. The rudder forward quadrant includes the quadrant and jackshaft.
C. This procedure is applicable for the captain’s and first officer’s rudder forward quadrants.
TASK 27-21-51-000-801
2. Rudder Forward Quadrant Removal
(Figure 401, Figure 402, Figure 403)
A. References
Reference Title
27-21-00-800-802 Remove Pressure from the Rudder Hydraulic Systems A, B, and
Standby (P/B 201)
31-31-42-000-801 Rudder Pedal Position Sensor Removal (P/B 401)
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1585 Kit - Rigging Pins, All Systems
(Part #: F70207-109, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
C. Location Zones
Zone Area
112 Area Forward of Nose Landing Gear Wheel Well
D. Access Panels
Number Name/Location
112A Forward Access Door
113AC Fwd Nose Wheel Well Upper Access Panel
114AC Fwd Nose Wheel Well Upper Access Panel
311BL Stabilizer Trim Access Door
324CL Vertical Fin, Access
E. Prepare for the Removal
SUBTASK 27-21-51-860-001
WARNING: MAKE SURE THE DOWNLOCK PINS ARE INSTALLED ON ALL THE LANDING GEARS.
WITHOUT THE DOWNLOCK PINS, THE LANDING GEARS COULD RETRACT AND
CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) Do this task: Remove Pressure from the Rudder Hydraulic Systems A, B, and Standby,
TASK 27-21-00-800-802.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-21-51
Page 401
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-21-51-010-001
(2) To get access to the rudder feel and centering unit, do this task:
Open this access panel:
Number Name/Location
324CL Vertical Fin, Access
SUBTASK 27-21-51-080-001
(3) Install rig pin R-5 from the rig pin kit, SPL-1585 in the rudder feel and centering unit (Figure 401).
SUBTASK 27-21-51-010-008
(4) Open this access panel:
Number Name/Location
311BL Stabilizer Trim Access Door
SUBTASK 27-21-51-010-002
(5) Open this access panel:
Number Name/Location
112A Forward Access Door
SUBTASK 27-21-51-010-003
(6) Remove these access panels:
Number Name/Location
113AC Fwd Nose Wheel Well Upper Access Panel
114AC Fwd Nose Wheel Well Upper Access Panel
and .
SUBTASK 27-21-51-020-001
(7) For the first officer’s rudder forward quadrant, remove the rudder pedal position sensor. To
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊2(91)