曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

SUBTASK 27-21-00-410-018-001
(19) Close this access panel:
Number Name/Location
117A Electronic Equipment Access Door
------------------------- END OF TASK ---------------------------
TASK 27-21-00-700-823-001
17. Rudder Hinge Friction Test
Figure 503
A. General
(1) Use this test to verify that the rudder hinge friction is within limit.
B. References
Reference Title
27-21-00-800-802 Remove Pressure from the Rudder Hydraulic Systems A, B, and
Standby (P/B 201)
C. Tools/Equipment
Reference Description
STD-753 Scale - Push/Pull, 0-25 pound (0-11 kilogram) Capacity, 1/4 pound
(113 gram) Accuracy
STD-1238 Indicator - Dial
STD-1278 Block - Loading, 1/8 Inch Thick, 3 Inch by 3 Inch Wood or Fiberglass
Block with Pad to Prevent Damage to the Skin.
STD-1279 Mount - Device, Mounting, Holds the Dial Indicator
D. Location Zones
Zone Area
324 Vertical Fin - Rear Spar To Trailing Edge
E. Procedure
SUBTASK 27-21-00-860-120-001
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDER,
ELEVATORS, FLAPS, SPOILERS, SLATS, AND THRUST REVERSERS CAN MOVE
QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO
PERSONS AND DAMAGE TO EQUIPMENT.
(1) If hydraulic pressure is powered, do this step to turn off hydraulic power:
(a) Do this task: Remove Pressure from the Rudder Hydraulic Systems A, B, and Standby,
TASK 27-21-00-800-802.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 001-005, 155-157, 201-999 PRE SB 737-27-1253 27-21-00
Config 1
Page 565
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-21-00-730-025-001
CAUTION: USE A LOADING BLOCK AND DO NOT PUT MORE THAN 50 LBF (222 N) ON THE
RUDDER WHEN YOU MOVE THE RUDDER SURFACE BY AN EXTERNAL FORCE.
APPLY THE EXTERNAL FORCE APPROXIMATELY AT BETWEEN 6 INCHES (162
MILLIMETERS) AND 18 IN. (457 MM) FROM THE BOTTOM OF THE TRAILING EDGE
AND APPROXIMATELY 3 IN. (76 MM) FORWARD OF THE TRAILING EDGE. IF YOU DO
NOT APPLY FORCE AT THIS LOCATION, YOU CAN CAUSE DAMAGE TO THE RUDDER
(2) Do the rudder hinge friction check:
NOTE: If the dial indicator is not available, you can use a ruler to measure the rudder trailing
edge placement in this test.
(a) Make sure the rudder and rudder pedals are in the neutral position.
(b) Make sure the rudder trim indicator is at zero units of trim.
(c) Use a block, STD-1278 and push/pull scale 0-25 pound (0-11 kilogram), STD-753 to move the
rudder fully to the left side.
1) Verify that there is no sign of binding, rough spots or excessive friction at any point of
travel.
a) If binding or excessive friction exist, the bearings may be out of alignment,
damaged or improperly installed. Correct this condition and repeat this check.
(d) Use a block, STD-1278 and push/pull scale 0-25 pound (0-11 kilogram), STD-753 to move the
rudder fully to the right side.
1) Verify that there is no sign of binding, rough spots or excessive friction at any point of
travel.
a) If binding or excessive friction exist, the bearings may be out of alignment,
damaged or improperly installed. Correct this condition and repeat this check.
(e) Attach the mount, STD-1279 on the tail cone.
(f) Place the pointer of the dial indicator, STD-1238 at the lower aft corner of the rudder trailing
edge.
(g) Use a block, STD-1278 and push/pull scale 0-25 pound (0-11 kilogram), STD-753 to move the
rudder 2.25 ±0.10 in. (5.72 ±0.26 cm) to the left side.
1) Verify that the force to move the rudder is less than 16.3 lbf (72.51 N).
(h) Use a block, STD-1278 and push/pull scale 0-25 pound (0-11 kilogram), STD-753 to move the
rudder 2.25 +/- 0.1 inches (5.72 +/- 0.25 centimeters) to the right side.
1) Verify that the force to move the rudder is less than 16.3 lbf (72.51 N).
(i) Remove the dial indicator, STD-1238 and block, STD-1278 from the rudder.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 001-005, 155-157, 201-999 PRE SB 737-27-1253 27-21-00
Config 1
Page 566
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
RUDDER AND RUDDER TRIM CONTROL SYSTEM - ADJUSTMENT/TEST
1. General
A. This procedure has these tasks:
(1) Rudder Forward Quadrant Adjustment - Use this task to adjust the rudder forward quadrant.
(2) Rudder Pedals Adjustment - Use this task to adjust the rudder pedals.
(3) Rudder Control Cables RA and RB Adjustment - Use this task to adjust the rudder control cables.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊2(47)