曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

POST SB 737-27-1253
27-21-00
Config 2
Page 547
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-21-00-860-102-002
(3) Do this task: Put the Rudder Hydraulic systems A, B, and Standby Back to the Condition
Before the Pressurization, TASK 27-21-00-840-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 006-099, 101-122; GUN 001-005, 155-157, 201-999
POST SB 737-27-1253
27-21-00
Config 2
Page 548
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Rudder Hinge and PCU Bearing Freeplay Check
Figure 503/27-21-00-990-818-002
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 006-099, 101-122; GUN 001-005, 155-157, 201-999
POST SB 737-27-1253
27-21-00
Config 2
Page 549
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-21-00-700-815-002
9. Rudder Centering Test
A. General
(1) Use this test to make sure the rudder is in its center position.
B. References
Reference Title
24-22-00-860-811 Supply Electrical Power (P/B 201)
24-22-00-860-812 Remove Electrical Power (P/B 201)
27-21-00-800-801 Rudder Hydraulic System A, B, or Standby Pressurization (P/B 201)
27-21-00-840-801 Put the Rudder Hydraulic systems A, B, and Standby Back to the
Condition Before the Pressurization (P/B 201)
34-21-00-820-801 Air Data Inertial Reference System - Alignment from the FMC CDU
(P/B 201)
34-21-00-820-802 Air Data Inertial Reference System - Alignment from the ISDU
(P/B 201)
C. Location Zones
Zone Area
211 Flight Compartment - Left
212 Flight Compartment - Right
325 Vertical Fin - Rudder
D. Procedure
SUBTASK 27-21-00-860-103-002
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDER,
ELEVATORS, FLAPS, SPOILERS, SLATS, AND THRUST REVERSERS CAN MOVE
QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE INJURY TO
PERSONS AND DAMAGE TO EQUIPMENT.
(1) Pressurize the rudder hydraulic systems A and B. To pressurize them, do this task: Rudder
Hydraulic System A, B, or Standby Pressurization, TASK 27-21-00-800-801.
SUBTASK 27-21-00-860-104-002
(2) Do this task: Supply Electrical Power, TASK 24-22-00-860-811.
SUBTASK 27-21-00-860-105-002
(3) Align the ADIRS. To align the ADIRS, do this task: Air Data Inertial Reference System -
Alignment from the ISDU, TASK 34-21-00-820-802 or Air Data Inertial Reference System -
Alignment from the FMC CDU, TASK 34-21-00-820-801.
SUBTASK 27-21-00-730-018-002
(4) Do the test of the rudder centering test:
(a) Make sure the rudder is in the neutral position.
1) If it is necessary, move the rudder pedals lightly to set the rudder to the neutral
position.
(b) Make sure that the rudder trim indicator is at 0.0 ± 0.25 units of trim.
(c) Move the captain’s left rudder pedal approximately 0.5 in. (12.7 mm) forward and release.
1) Make sure the rudder goes back to the neutral position.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN 006-099, 101-122; GUN 001-005, 155-157, 201-999
POST SB 737-27-1253
27-21-00
Config 2
Page 550
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(d) Move the captain’s right rudder pedal approximately 0.5 in. (12.7 mm) forward and release.
1) Make sure the rudder goes back to the neutral position.
(e) Set FLT CONTROL A and B switches to the STBY RUD position.
1) Make sure that the STANDBY HYD LOW PRESSURE light on the P5-3 panel
extinguishes.
(f) Set the YAW DAMPER switch on the P5-3 overhead panel to the ON position.
(g) Do these steps to initiate a zero yaw damper command output from the stall Management
Yaw Damper No. 2 (SMYD No. 2), M1748:
NOTE: The SMYD No. 2 is installed on the E3-2 electrical equipment rack.
1) Push and release the ON/OFF button on the front BITE display of the SMYD No. 2.
2) Push and release the up arrow or down arrow button until the GROUND TEST shows on
the display.
3) Push the YES button to get access to the ground test option.
4) Push and release the up arrow or down arrow button until the SERVO TEST? shows on
the display.
5) Push the YES button to start the servo test.
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE
RUDDER. THE RUDDER CAN MOVE QUICKLY WHEN YOU PUSH THE
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊2(66)